GTW540ASP0WS General Electric Washer - Overview
Sections of the GTW540ASP0WS
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
LID LOCK SERVICE KIT
PartSelect #: PS17626546
Manufacturer #: WH08X37938
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
$73.45
In Stock
Drain Pump
PartSelect #: PS12723115
Manufacturer #: WH23X28418
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
$44.95
In Stock
Water Inlet Valve Assembly
PartSelect #: PS12726769
Manufacturer #: WH13X26535
NO LONGER COMES W/GASKET, PER GE
$45.95
In Stock
Rod & Spring Assembly
PartSelect #: PS12343380
Manufacturer #: WH16X26910
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and ...
$19.95
In Stock
Rod & Spring Assembly
PartSelect #: PS12343381
Manufacturer #: WH16X26911
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your wa...
$21.95
In Stock
CLUTCH
PartSelect #: PS11729473
Manufacturer #: WH05X24185
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
$33.95
In Stock
MODE SHIFTER
PartSelect #: PS16554752
Manufacturer #: WH03X30517
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
$49.93
In Stock
DRIVE BELT
PartSelect #: PS11736832
Manufacturer #: WH01X24180
This drive belt is sourced from the original manufacturer for use in various models of dryers. It is a rubber belt that connects the motor to the transmission of the washer. It enables the drum to spi...
$25.95
In Stock
Lid Lock Bezel
PartSelect #: PS11736833
Manufacturer #: WH01X24381
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the peri...
$13.95
In Stock
SPEED SENSOR
PartSelect #: PS16619248
Manufacturer #: WH03X32158
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
$33.95
In Stock
SPRING CLUTCH
PartSelect #: PS11763251
Manufacturer #: WH01X24434
Introducing the GE Spring Clutch, a crucial component for your washer. This intricate item applies steadfast pressure against the shifter hub, dutifully holding it in place for uninterrupted operation...
$13.95
In Stock
Questions And Answers for GTW540ASP0WS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Henry
November 15, 2024
Making a loud squeaking noise during wash cycle
For model number GTW540ASP0WS
Hello Henry, Thank you for reaching out. We suggest checking the Drive Belt for wear or damage. The belt is prone to wear over time due to the high friction it experiences. Thank you for the inquiry, good luck with the repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
DRIVE BELT
$25.95
In Stock
- < Prev
- 1
- Next >
Common Symptoms of the GTW540ASP0WS
[Viewing 14 of 14]Will not drain
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Draining Issues
Fixed by
these parts
these parts
Show All
Cycle Not Advancing
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer ran fine but woudl not drain water - low humming noise
Drain all the water out of the tub with a shop vac
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps ... Read more from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Read less
Parts Used:
-
Mike from NAPLES, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
56 of 79 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wife pull up door when it was in lock mode
Lift up door removed lid lock with screwdriver installed new part
Parts Used:
-
Wiley from Wilson, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
52 of 94 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not drain the water from the tub.
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Parts Used:
-
Micheal from South Bend, IN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
33 of 50 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!