Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This is a drive belt for various models of dryer. This belt is responsible for allowing the drive motor to rotate the dryer drum. Over time and with use, this belt will wear out and if it becomes dama...
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and ...
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your wa...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger...
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the peri...
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
The agitator rotates back and forth to move the clothes inside the tub to clean the load.
$50.44
In Stock
Questions And Answers for GTW460ASJ9WW
Ask our experts a question about this model and we'll get back to you as soon as possible!
23 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Terry
November 11, 2021
Doesn't use enough cold water even on highest water level. The clothes don't all get wet unless I stand and spin the tub while it is filling. Then the clothes all get bunched up on one side of the tub, which of course, throws it out of balance. Nigh to impossible to spread the clothes out so it balances the load and the machine doesn't go crazy banging and shaking. Twists clothes together and some items wind up inside other items.
For model number GTW460ASJ9WW
Hello Terry, Thank you for the question. We suggest checking to make sure the Cold Water Tap is on all the way. If the water Flow is still slow, you may need to replace the Water Inlet Valve, PartSelect Number: PS12726769. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
the washer wont fill, i checked the water inlets and both clear, i change the lid lock switch im reaching the point of total frustration
For model number GTW460ASJ9WW
Hi Todd, thank you for getting in touch. Based on our understanding of the issue, we would recommend checking the selector switch assembly, part number PS12754096, as it is most likely faulty and may need to be replaced. We hope this sorts out your problem!
STARTS BEEPING WHEN ITS NOT RUNNING. SOUNDS LIKE MOORIS CODE.
For model number GTW460ASJ9WW
Hi Craig, thank you for contacting us. Based on our research, the beeping occurs if the interface control board is shorting out. It comes along with the control panel assembly, part number PS12703270. You may need to replace it to fix the issue. We hope this information helps!
Hello Ricky, Thank you for the question. This could be an indication the Mode Shifter is faulty and may need to be replaced. We also suggest testing the Lid Switch assembly. If defective it will think the lid is open and it is not safe to spin. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Washer intermittently will fill and agitate but won't drain and spin. Beeper for it being finished will sound but still full of water. Will normally correct itself eventually after using the drain and spin cycles multiple times or other times will just finish on its while we are away
For model number GTW460ASJ9WW
Hi Bill, thank you for contacting us. Based on our understanding of the issue, the problem is most likely related to the main control board, part number PS16743401. We hope this solves your problem!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
