Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and ...
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your wa...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger...
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the peri...
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
Introducing the GE Spring Clutch, a crucial component for your washer. This intricate item applies steadfast pressure against the shifter hub, dutifully holding it in place for uninterrupted operation...
$13.95
In Stock
Questions And Answers for GTW460ASJ7WW
Ask our experts a question about this model and we'll get back to you as soon as possible!
18 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
LISA
May 3, 2023
SQUEEKING, CHIRPING LIKE METAL ON METAL SOUND WHILE AGITATING.
For model number GTW460ASJ7WW
Hi Lisa, thank you for reaching out. Based on our understanding of the issue, we would suggest you check the clutch, part number PS11729473, as it is the most likely cause of this issue. If it is faulty, you may need to replace it. We hope this solves your problem!
Machine is making squealing sound and clothes are very wet at end of cycle
For model number GTW460ASJ7WW
Hello Duke, thank you for your question. Overloading can lead to an imbalance that reduces the washer's spin speed, leaving clothes too wet after spin cycle completes. If the washer leaves clothes soaked after a large load, remove some items, redistribute others and run another rinse and spin cycle. The squealing noise while running, the main culprit is usually worn Motor Pulley & Nut PartSelect Number PS16619249. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Jim
November 29, 2019
Washer will not spin..any suggestions what I need? thanks..jim
For model number GTW460ASJ7WW
Hi Jim, most likely fix is door lock PS12343280. Thank you for your question and good luck with your repair!
The washer will not drain or spin...doesnt seem to be moving to the next cycle. even placjng the washer on the drain and spin setting, the washers fills with water 1st, even its already over 1/2 full of water but empty of clothes, on the small load size setting, proceeds to a wash cycle, agitator ran for a regular amount of time, then it just stops with wash cycle and lid locked lights illuminated, but doesnt do anything else.
For model number GTW460ASJ7WW
Hello,
Thank you for your question. If the washer is not draining or spinning, the door lock may not be working correctly. If this part is malfunctioning, it can cause issues throughout the washer. There are some other parts that you should check as well. You will also need to check the lid lock striker, the speed sensor and the drain pump. You will need to test the electronic parts with a multi-meter. Here is a link to one of our videos on YouTube that you may use as a general reference on how to use one, https://www.youtube.com/watch?v=bWC44fHn0As. We hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jeff
June 16, 2021
My washing machine for no explainable reason will start beeping and lights will flash sometimes while it is running or not until we unplug it for a couple of hours
For model number GTW460ASJ7WW
Hello Jeff, Thank you for the question. In most cases the beeping indicates an issue with the Spin cycle. The appliance is sensing an off balance load or spinning slow. We suggest testing the Speed Sensor. If you are using a multi-meter to test the resistance, the readings should be around 1 or OL is it isn't defective. If it is closer to 0, then it is a short circuit and is defective. We hope this helps!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
