Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This is a drive belt for various models of dryer. This belt is responsible for allowing the drive motor to rotate the dryer drum. Over time and with use, this belt will wear out and if it becomes dama...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
This is an agitator assembly for washing machines. Agitators are used within top load washing machines to move back and forth and effectively wash your clothes. However, if the agitator currently in y...
This is a water inlet valve; an electrically controlled solenoid valve that opens and closes when necessary, to control the flow of water into your washing machine during the washing cycle. This part ...
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
Introducing the GE Spring Clutch, a crucial component for your washer. This intricate item applies steadfast pressure against the shifter hub, dutifully holding it in place for uninterrupted operation...
Presenting the GE Washing Machine Rod & Spring-Left-Blue designed specially to offer stability and robustness to your washing machine tub. This crucial component also comes with a susp, ball joint, an...
Presenting the GE SCR 1/4-20, 2A SINULOC Screw, a key component for ensuring the optimal functioning of your washers. This robust piece, designed with precision by GE, assures a safe and snug fit to m...
$13.95
In Stock
Questions And Answers for GTW220ACK7WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
10 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jerry
February 6, 2025
Does this model have motor coupling
For model number GTW220ACK7WW
Hello Jerry, thank you for reaching out. Based on our research, your model does not come with a motor coupling. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Darlene
October 16, 2024
Machine make a clicking noise and the lid will not lock or fill with water
For model number GTW220ACK7WW
Hi Darlene, Thank you for contacting us. If the lock is clicking but will not lock, it normally means the Lid Lock will need to be replaced. Good luck with the repair!
Is there a fabric softener dispenser with this model
For model number GTW220ACK7WW
Hi Doris, thank you for reaching out. Your model does not come with a fabric softener dispenser. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Doris
July 11, 2025
When should fabric softener be added to the wash?
For model number GTW220ACK7WW
Hello Doris, thank you for getting in touch. Fabric softener is typically added during the rinse cycle of a washing machine. If your washing machine is equipped with a fabric softener dispenser, you may introduce it at the start of the wash cycle, and it will be dispensed automatically during the rinse phase. In the absence of a dispenser, you should manually add the fabric softener to the full tub of water during the final rinse. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jeremy
January 25, 2024
Machine lid locks but no water pump into tub?
For model number GTW220ACK7WW
Hi Jeremy, thank you for writing in. Our research has found, 99% of the time it is the Water Inlet Valve, part number PS12726768 causing this issue. We hope this helps.
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conve
... Read morersation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
