All Installation Instructions for Husqvarna GTH264T

Wheel bushings were bad

Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.

Parts Used:

Lawn Mower Ring Clip

Lawn Mower Axle Hub Cap

Anthony from OLIVEHILL, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

22 of 36 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Original shield was damaged

Removed original shield ( 2 bolts), replaced with new shield.

Parts Used:

Lawn Mower Shield

Wayne from LAKEVILLE, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Worn out Mandrel Assemblies

Remove Deck, Remove Blades, Remove guards and belt, use old belt to hold pully to remove pully (would be good to have pully wrench), Remove mandrel Assembly, Install new mandrel assemblies (had to tap the new mandrel assemblies. Should have been done by manufacturer.). Reinstall blades, guards, and belt. Put deck back on.

Parts Used:

Lawn Mower Mandrel Assembly

Joseph from CANBY, MN
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Socket set

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Right axle bent

Replacing belt with no problem. I've ordered the front right axle spindle assembly three times. This is from your parts list and you sent me the part and they did not work at all.

Parts Used:

Lawn Mower Drive Belt

MATTHEW from PENNSBURG, PA
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Deflector shield cracked. Need to replace.

Mark the location of the spring so you know how it goes on. Snip off the push nut holding the deflector shield pin. Hammer the pin out. Insert the pin with the spring holding the new deflector shield. Use a socket to steady the push nut and hammer the pin into the push net until secure.

Parts Used:

Lawn Mower Push Nut

Lawn Mower Deflector Shield

Travis from PLATTE CITY, MO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Lound deck noise when mower put into motion

Parked mower on level concrete drive, laid on cardboard. Lowered mower deck all the way. Sparayed some WD40 on nut/bolt on top of old pulley. Since it is a carriage type bolt, placed 5/8" boxed end wrench over self locking nut on top of old pulley. Using some force from 3lb mallet to break nut free (hitting against wrench body), the nut came off easy as did broken pulley/bearing inside. Installed new pulley assembly, re-tightened nut on bolt. Checked after first mowing just to be certain pulley was in place and locking nut tight.

Parts Used:

Lawn Mower Pulley

Steven from Hickory, NC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set, Wrench set

4 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken v-belt for drive

I returned the belt because it was the wrong part. Ordered the correct belt from another source. After that the replacement went well and I crossed off Parts Select from my list.

Parts Used: