GSD42 General Electric Dishwasher - Instructions

I pulled the dishwasher out from under the counter. Loosened the collar holding the sump housing to the pump motor. Unscrewed the cover inside the base of dishwasher to release the collection opening of the sump. It's very flexible so I pulled it out by hand. Put the new one in and screwed everything back down. Pushed the dishwasher back under the counter. Simple Simple Simple.

First I replaced the flapper valve of of off the water pump. That worked for a couple of days, then the standing water was back. After more research at your site I ran across other person who had the same problem and they ended up replacing the piston and valve assembly. After pulling the dishwasher out I was able to find where these parts were located. The piston's rubber part was half gone. I replaced it and the gasket and another flapper valve. This model has two flapper valves. One difficulty was that you have to replace the screen inside the dishwasher before you replace the housing that the piston fits in. Your site and other folks contributing their stories helphed me to solve our problem. The dishwasher works like new now. Thanks. Ralph Naddeo.

My son found a water leak and cut the water supply off. He then pulled the machine from under the counter at which time I examined the valve under pressure and saw the leak. We cut the water off again and after tripping the circuit breaker we pulled the electrical connector and undid the mounting bracket which made getting the lines off the valve much simpler. New valve in hand I attached the lines and did a test then remounted the bracket and attached the electric. Easy as pie!

Unscrewed 2 screws from under the counter, pulled out dishwasher. Saw where it was leaking. Took wires loose, took the rack out, unscrew the white mesh, took out the dishwasher sump housing product saw a crack and ordered the piece. For anyone out there make sure you turn the electric power switch off before you attempt to fix anything!!!!!!

Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.

To remove the upper rack, twist the support rail end caps toward the center of the machine and slightly downward. The caps will come off and you can slide the new rack into place. Reverse the process to replace the end caps. One of mine broke and I will need to order replacements.
The original rack is no longer available. The replacement, which is the only one GE offers, has less storage space and is not as sturdy. It bends downward when full. I am very disappointed and recommend not replacing the rack unless you have no other choice.

It was tricky to get the old rack off. Usually you can unclip the clips closest to the front wheels to pull the rack out. However, there is an area behind one of the wheels that you can kind of release and than pull the rack out. You then have to slide out the funnel/fan piece from the middle. That piece slides/ snaps in the middle of the the new rack. Then slide the new rack in place, re attach the release used to slide oldrack out.
That is it !!

Research the problem on the internet .People suggestion was to replace the sequence switch . If this does not work replace the mother board .The sequence switch was replaced and fixed the problem .

with electric power and water source turned off,I first bailed out the water from tub then I pulled dishwasher out from under cabinet . Then I removed the motor and pump and put it on the table. I took a digital photo so I could remember exactly how everything was assembled. I checked for clogs and damage and realized that the solonoid casing had melted around the armature link assembly . I Looked at diagram for parts name and number and ordered from parts select. In the meantime I put a temporary one feed valve on hot water feed line so I could have access to hot water in kitchen while I waited for parts wich were here in a couple of days. Put it all back and it runs fine. Thank for your help

I unscrewed the check valve, tipped the dishwasher on its face, and removed the asembly below it. Then replaced the valve flapper, cleaned out the assembly (broken champagne glass and udder nasties) then put it back the way I found it.
Then I put the new check valve on, and started the dishwasher up.

10 screws and $30 worth of parts saved me 400 bones for buying a new dishwasher.


If you have sanding water in your dishwasher check these two parts.....that check valve is the culpret.

At first I found some water on my hardwood floor by the dishwasher, I thought that I might spilled't the day before, then it hapened again, so I remover the front lower cover for the dishwasher and I found water under the dishwasher, then I turned on the machine and I found a pin hall water leak from the water inlet valve. I turned the machine off, then I closed the water valve under the sink, then I disconected the power plug from the valve, the diconected the water supply copper pipe, then diconected the house from the valve to dishwasher, then got the part# from the valve sticker and the model# for the dishwasher from inside of the door. after that I went online and I got the valve. make sure to try more than one website because they all have differant prices, and Parts Select was the lowest one.

Removed the dishwasher from the cabinet. Turned it on it's top side. Removed the exit hose from the pump with a nut driver and replaced the flapper. Reconnected the hose to the pump.

Replaced with a new rinse aid fill cap.

I removed the scews holding the inside door to the outside door section. Once removed I removed the 2 screws that held the switch to the door. After removing this switch I had to open it up to expose the four wires on the switch. I reattached the four wires to the new switch closed it up and placed it on the door with the 2 screws.
Replaced the inside door. Job finished with the switch working and the dishwasher operating as per the factory standards.
Very easy job and by doing it myself I saved money on a service call.

The leak was coming from the drain valve shaft and I found the tips to replace the seal from this website. I was able to reach everything without removing the dishwasher from the cabinet. Once I got the cam lifter off the old push on nut was corroded so it was easy to get off. The old seal was recessed so I used the point of an ice pick to gently pry it out. The new seal was easy to push in place but the push on nut was a bear. I saw other comments about using a deep socket to push it on but I didn't have one the right size. I was able to hold the end of the shaft with pliers and pushed the nut in place using a screwdriver. Ran a short cycle and no more leak. Thank goodness for this website. Found the part easily and the other written comments were very helpful.