FX710BGS (XAA-0003) Samsung Range - Overview
Sections of the FX710BGS
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Burner Igniter
PartSelect #: PS4241428
Manufacturer #: DG94-00520A
This is an oven burner igniter made for use with Samsung ovens. This oven burner igniter is designed to ignite the gas that flows into it, to produce heat. However, over time and with further frequent...
$216.95
On Order
Temperature Sensor
PartSelect #: PS4240743
Manufacturer #: DG32-00002B
This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will ...
$125.95
In Stock
Leveling Leg
PartSelect #: PS4240934
Manufacturer #: DG61-00525A
The Black Leveling Leg from Samsung is a durable, genuine part designed for use with many Samsung kitchen appliances. This quality leg-leveling device offers an easy-to-use design to correct uneven su...
$36.95
On Order
Surface Burner Knob
PartSelect #: PS10058981
Manufacturer #: DG64-00472A
The surface burner knob lets you control the heat of the surface burner on the range.
$30.95
On Order
Range Right Rear Burner Cap (Black)
PartSelect #: PS5576950
Manufacturer #: DG62-00111A
This surface burner cap is specially designed to fit with Samsung ranges. It is a genuine OEM replacement part supplied directly by Samsung to ensure compatibility. The burner cap is a round, black ca...
$50.95
In Stock
Rubber Cushion
PartSelect #: PS4241222
Manufacturer #: DG73-00003A
This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It preven...
$6.95
In Stock
Burner Cap
PartSelect #: PS4240973
Manufacturer #: DG62-00070A
Enjoy the precision and durability of Samsung with this high-quality Left Rear Burner Cap. Known as the "surface burner cap", this essential component is designed to cover the surface burner of your S...
$63.95
In Stock
Bottom Floor Panel
PartSelect #: PS4240944
Manufacturer #: DG61-00570A
This oven cavity floor coating or bottom floor panel is an authentic OEM part supplied by Samsung to ensure compatibility with various models of Samsung ranges. It is a protective layer that sits on t...
$149.95
In Stock
Wire Rack
PartSelect #: PS12721757
Manufacturer #: DG75-01001D
This stainless steel wire rack is a sturdy platform for baking or roasting food, making sure heat circulates evenly. It measures approximately 7/16 inches by 24 3/4 inches and is usually found inside ...
$133.23
In Stock
Surface Burner Cap
PartSelect #: PS4240971
Manufacturer #: DG62-00067A
The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
$77.95
In Stock
Burner Head
PartSelect #: PS5576948
Manufacturer #: DG62-00076B
The Samsung Burner Head (Aux) is a top-notch enhancement for your Samsung range. Specifically designed to endure high temperatures, this quality part, crafted from sturdy metal, ensures durability and...
$54.95
In Stock
Burner Head
PartSelect #: PS8764922
Manufacturer #: DG62-00074C
Introducing the robust Samsung Right Burner Head, a full-length surface burner designed especially for Samsung ranges. Manufactured from hard-wearing metal, this genuine OEM item ensures exceptional d...
$75.95
In Stock
Questions And Answers for FX710BGS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the FX710BGS
[Viewing 6 of 6]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not heating and holding temp
The Samsung stove I have has had the igniter replaced several times. It seems to wear out over a couple years time. I did the repair with a Philips #2 screw driver. Open the oven door, remove the grates. unscrew the bottom cover and expose the heat shield. Unscrew the heat shield. This exposes the burner. Unscrew the burner from the c
... Read more
enter of the plate/lower heat shield. Unscrew the burner from the front and back of the oven. Carefully lift up the burner to expose the igniter and clip. Unscrew the igniter from the burner and set the burner aside. Unclip the igniter from the power cable. If it falls below, it won't go far just reach in a lift it back up to fasten the new igniter to the power clip. Refasten to the burner with new clips and screws provided. Re-insert the burner to the gas jet that is below the bottom plate which will not be visible to you unless you place your head towards the rear of the stove and look down. Once the Jet is back into the hole of the burner, re fasten it to the middle back and front of the stove. Replace the covers and grates. Close the oven and test it. A new igniter does wonders. You can remove the stove door for a less intrusive install, but I found it unnecessary to do so and saved a step and time. I was done well under 30 minutes.
Read less
Parts Used:
-
John from EAST QUOGUE, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
17 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat consistently
My barely 4 year old Samsung range/oven began not heating consistently. Even though it said 350, for example, we had to increase to 465 to get it to bake. Thought it was the temperature sensor. Ordered and installed new one easily. That didn't solve the problem. So, rather than throw more money at parts that may not have resolved the
... Read more
issue, I got a new Amana range. Samsung appliances go to my 'do not buy' list along with LG!
Read less
Parts Used:
-
Steven from CHEYENNE, WY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
18 of 36 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven will not come to desired temp setting
ordered the temp sensor for a standard complaint, new sensor was the correct part ordered, however, once the old sensor was removed, I ohm'd the original and the new part. Both were 1080, checked wiring, checked gas burner, checked line voltage. Searched other part prices, found Samsung to be a not desirable product to own. This non repai
... Read more
r was to help my neighbor who lives on a fixed income. Checked oven temp with the oven at 350 f setting, oven was 223 f. Set oven to 465 f and fount the oven at 353 f. I wanted to return the part but she insisted I install it anyway and found the oven doing the same thing. She did not want to throw more money at a 4 year old range. Will use it as it is but will buy a cheap oven temp gauge. Samsung sucks.
Read less
Parts Used:
-
DAVID from BIRDSBORO, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
11 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!