EFDC317TIW2 Frigidaire Dryer - Overview
Sections of the EFDC317TIW2
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
High Limit Thermostat
PartSelect #: PS446428
Manufacturer #: 3204267
This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will cut it out and only c...
$57.77
In Stock
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$21.95
In Stock
Belt
PartSelect #: PS2349294
Manufacturer #: 134719300
This dryer belt is one of the most important parts in a dryer and is what allows the dryer drum to spin/rotate. If the dryer belt is damaged or broken, the drum will not spin or will have difficulty i...
75% OFF
$13.49
$53.71
In Stock
High Temperature Adhesive
PartSelect #: PS474458
Manufacturer #: 5308027429
This high temperature adhesive is used for installing felt and rubber seals on dryers. The tube contains 1 ounce of product. This adhesive is made to withstand extremely hot temperatures. Before apply...
$49.95
In Stock
Thermal Fuse
PartSelect #: PS2349395
Manufacturer #: 137032600
Discover the quality and reliability of genuine Frigidaire parts with this Thermal Limiter. Specially designed to protect from overheating, this non-resetable thermal fuse shuts off your dryer's heate...
$36.95
In Stock
Drum Roller
PartSelect #: PS12741852
Manufacturer #: 5304523152
Dryer drum rollers are parts that support the dryer drum. They allow the drum to rotate smoothly and cut down on the friction between the drum and the dryer frame. They are usually made of metal or pl...
$34.95
In Stock
Dryer Drum Roller Kit
PartSelect #: PS12746506
Manufacturer #: 5304523155
This is a genuine replacement drum roller for a dryer. This part includes a roller which has an axle and two tri-rings. The dryer drum roller holds the drum in place while it rotates on the dryer supp...
$73.67
In Stock
MOTOR
PartSelect #: PS16620747
Manufacturer #: 5304529782
This drive motor includes the pulley for the dryer drum belt. The motor has reverse threads for the blower wheel. Please disconnect the power before starting your repair. This is a genuine OEM part.
$168.76
In Stock
HEATER,ELEMENT,4700W
PartSelect #: PS17219736
Manufacturer #: 5304535760
50% OFF
$37.99
$75.61
In Stock
Idler Arm Spring
PartSelect #: PS418263
Manufacturer #: 131601000
Revitalize your dryer with the genuine OEM idler arm spring idler pulley spring from Frigidaire. Expertly crafted to keep the idler pulley tight against the drum belt, this part facilitates smooth and...
$50.44
In Stock
Questions And Answers for EFDC317TIW2
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the EFDC317TIW2
[Viewing 6 of 6]Noisy
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Noisy Dryer
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replac
... Read more
ing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
Read less
Parts Used:
-
Philip from Oakland, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
55 of 67 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Excessive lint build up in fan blades of Electrolux 617 series dryer
I watched and re-watched a YouTube video where these parts were recommended for a retro fit of the Electrolux 617 dryer. The original parts for this dryer allow too much lint to get past the lint screen and into the fan blades. To install these new parts you just need to be careful to pull the moisture sensor leads off of the old grill as
... Read more
sembly and put them on to the correct prongs on the new grill assembly. (You will not use the leads that the new parts come with.) You may want to take a picture of how the leads were on the old assembly before you pull them off. You also need two, two-inch #10 screws that are readily available at hardware stores. I bought the "sheet metal" type screws. The YouTube video can be found by entering the words "Electrolux Dryer Lint Fix & Retrofit" into Google or YouTube search bar. If you follow it to the letter all will be well, but be careful to line up the holes for the screws. Having someone else holding a flashlight would be ideal, but it's not absolutely necessary.
So does this work? Yes, the parts fit just fine and they improve the situation a great deal but they don't completely solve it if you have a dog that has those little short sharp hairs and the dog sleeps in your bed, sits on your lap and leaves dog hair all over stuff that will be washed and put into the dryer. Those hairs will still get past the new clam shell filter but the good news is, you don't have to pull the dryer apart to clean the fan blades after you have installed these new parts. You can take the hose from your vacuum cleaner and just stick it in the fan blade compartment (after removing clamshell lint screen) and you will be able to capture most of what got past the screen. How is this different than before? The kind of lint that makes it past the new parts is much lighter and finer than what got past the old screen so the vacuum can easily pull it out.
PS I love Parts Select. This is the second thing I've ordered from them and I've been so impressed with how fast the parts arrived and how nicely they were packed. It's a first class organization in my opinion.
So does this work? Yes, the parts fit just fine and they improve the situation a great deal but they don't completely solve it if you have a dog that has those little short sharp hairs and the dog sleeps in your bed, sits on your lap and leaves dog hair all over stuff that will be washed and put into the dryer. Those hairs will still get past the new clam shell filter but the good news is, you don't have to pull the dryer apart to clean the fan blades after you have installed these new parts. You can take the hose from your vacuum cleaner and just stick it in the fan blade compartment (after removing clamshell lint screen) and you will be able to capture most of what got past the screen. How is this different than before? The kind of lint that makes it past the new parts is much lighter and finer than what got past the old screen so the vacuum can easily pull it out.
PS I love Parts Select. This is the second thing I've ordered from them and I've been so impressed with how fast the parts arrived and how nicely they were packed. It's a first class organization in my opinion.
Read less
Parts Used:
-
Suzanne from PALM SPRINGS, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
9 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cloths not drying
Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap
Parts Used:
-
keith from ELLENVILLE, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers, Socket set
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!