Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
DDT595SMJ2ES General Electric Dishwasher - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The lower rack roller supports the smooth sliding of your dishwasher’s bottom rack. Measuring 1.5 inches in diameter and charcoal-colored, this OEM replacement part is sold individually. Replace all f...
This lower spray arm assembly in your dishwasher distributes water and detergent during the washing cycle by spinning around and spraying water in different directions. You can usually find it attache...
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
The element heating assembly is found at the bottom of the dishwasher tub, and helps to warm the water in the wash cycle, and dry the dishes afterward. If the water does not heat up during the wash cy...
- Includes: 4 brackets, 4 roller wheel brackets, and 8 wheels part # WD12X26146
Dishwasher Lower Dishrack Carrier and Roller Kit (Set of 4). This kit will replace all four one piece roller carriers w...
This is a washer inlet valve assembly for your dishwasher. This valve allows water to flow into your dishwasher at the proper rate. If your dishwasher tub is not filling with water or filling when the...
This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the c...
This drain pump kit is for dishwashers. The drain pump kit removes the water from the dishwasher tub during the drain phase of the dishwashing cycle. The kit may include multiple parts; refer to your ...
This OEM mid spray or center wash arm assembly distributes water and detergent in your dishwasher during the wash cycle. It has small nozzles that spray water onto your dishes and is located between t...
This OEM-compatible screw is designed for use with many GE dishwashers. Measuring 8-16 HXW and 1/2" in length, this stainless steel screw secures the middle spray arm hub to the upper rack assembly, e...
The detergent dispenser in your dishwasher stores the detergent until it is ready to be dispensed. If your dishes are not coming clean, or you notice the detergent is still in the dispenser at the end...
This electronic control board is for dishwashers and manages the functions of the dishwasher such as washing, draining and drying.
$175.91
In Stock
Questions And Answers for DDT595SMJ2ES
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rick
November 16, 2022
I submitted a question 5 days ago regarding the user interface does not light up at all. I've replaced both the interface board and the main control board. I have 14 volts DC to the interface board connector. Shouldn't I see something on the display illuminated?
For model number DDT595SMJ2ES
Hello Rick, thank you for your inquiry. According to our research, we would recommend you check the wires attached from the main control board to the interface board. If the wires look good, you may need to replace a silicon light pipe, part number PS8756259. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
I have 120 volts to the dishwasher. There is no display on the control panel. I checked and there is 14 VDC to the user interface board. I replaced this board and set the personality according to the model #. After reassembly I still have no display. Suggestions?
For model number DDT595SMJ2ES
Hello Rick, thank you for contacting us. We would recommend testing the control board, part number PS12730509, and the UI control board, part number PS12113186, using a multimeter to pinpoint the fault. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
I need the silver plastic strip that goes on three sides of the top control panel
For model number DDT595SMJ2ES
Hi Fran, thank you for reaching out. The plastic strip you are looking for comes attached with a control panel, part number PS11772022. We hope this helps!
Hello John, thank you for your question. We do not see a part 632 but for part 586, For your convenience, we have attached the link to our repair video. We hope this helps. Good luck with your repair https://www.youtube.com/watch?v=oaDc1FMgAuA.
Was this helpful?
Thank you for voting!
Jared
January 31, 2025
My dishes are coming out soaking wet and not fully clean
For model number DDT595SMJ2ES
Hello Jared, thank you for your question. This can be caused by a faulty Heating element PS16729156, the Flood Switch PS12068856 (This part shuts the water fill valve off if the water level gets too high before the timed fill cycle ends.) and the Vent Fan PS8767438. If the vent fan motor is malfunctioning the dishes may not dry as expected. We have a video on how to test each component with a multimeter. Good luck with your repair.
Didn't actually do the compete repair but got close. Pulled out dishwasher, disconnected and checked continuity on the existing heating element (about 16 ohms) the new element was also about 16 ohms. This indicates they both were working fine and no need for replacement. Next step would have been to swap the elements would have been
... Read moresimple. Tried to replace main board as well, still not the issue so giving up and replacing the dishwasher. It wasn't the high temp cut off thermostat either incidentally and no error codes in maintenance mode. Check continuity of your existing element before ordering to save aggravation.
Open the washer, remove the bottom dish rack, then twist off the bottom water sprayer. Use a screwdriver to remove the mounting/ stabilizing screws so you can slide out the dishwasher. Close the dishwasher and slide it out. Underneath at the back there are two wires powering the drying element, carefully remove them. Use an adjustable wre
... Read morench to remove the two plastic mounting nuts for the drying element. Open the washer and remove the old drying element, and insert the new element. Reassemble the dishwasher in the reverse order if disassembly.
1. Turn off breaker supplying power to dishwasher in electrical panel 2. Open dishwasher door 3. Unscrew the screws that secure the dishwasher to the counter. 4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch. 5.
... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside. 6. Remove old door latch. 7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in. 8. Plug wire harness into new door latch. 9. Re-align dishwasher and re-secure to counter in previous position. 10. Test latch to make sure it closes properly. 11. Turn on breaker in electrical panel. The dishwasher should now function properly.
