Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for ...
This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if...
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
This light bulb, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can so...
This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep yo...
The drum slides are not included with this part. The top bearing helps your dryer operate as quietly as possible. This part will require two green drum slides and 2 white drum slides.
This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on ...
Keep your GE dryer running smoothly with this genuine OEM rear drum bearing sleeve, designed specifically for GE dryer models. This part supports the back of the dryer drum and helps reduce friction a...
TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the...
This authentic OEM rear bearing O-ring is designed for use with GE dryers. It helps secure the drum rear bearing onto the drum shaft, playing a key role in maintaining smooth and quiet dryer operation...
Ask our experts a question about this model and we'll get back to you as soon as possible!
8 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Wayne
January 19, 2020
GE dryer i cannot change the time with the + and buttons. The clean vent light is on, i keep it clean each time it is used. Thanks wayne
For model number DBVH520EJ2WW
Hello, Thank you for your question. You will need to check into: Part #: PS1482261. This is the main control board that operates the unit. We hope this helps, good luck with this repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Dave
December 27, 2024
Push on button Time lights up Push start button , and hear it click but does not start But the timer still counts down ?
For model number DBVH520EJ2WW
Hello Dave, thank you for your question. Typically, when you hear a click but nothing happens when you try to start your dryer, it could be a problem with the thermal fuse PS267900. It cuts off power to the dryer motor if the temperature reaches an unsafe level. If you push the start button and nothing happens, the high-limit thermostat should be tested for continuity and replaced if the contacts are open. We hope this helps.
How do i repair the paint that is peeling around the back wall of the drum?
For model number DBVH520EJ2WW
Hello Brenda and thank you for writing.
The paint. This part is discontinued for your model and is no longer available. We have no known replacement information in our system. We recommend you contact the manufacturer of the part to see if they have recently released a new substitute. You might be able to pick up a metal paint spray at a local hardware store or home depot, that should do the trick. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
Jennifer
July 22, 2022
In the past few months the top of my dryer is peeling.
For model number DBVH520EJ2WW
Hello Jennifer, thank you for your question. We do sell the Top Panel PS1017066 as well as the Front Panel PS1017082. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Dryer starts most of the time, but then stops. Doesn't dry clothes
For model number DBVH520EJ2WW
Hi Susan, thank you for asking. If your dryer starts and stops without drying clothes, you may need to check the moisture sensor, part number PS1021860, to fix the issue. It detects the amount of moisture in the laundry load and signals the control board when to stop. We hope this sorts out your problem!
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and
... Read more drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
1. Removed top cap on lid by removing the 3 - phillips screws. 2. removed front digital display panel from PC board. 3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit. 4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this fram
... Read moree. 5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides. 6. Re-installed all wiring and panels.
*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on. This was a first attempt ever at fixing an appliance and it was no big deal.
