D1436TB LG Dishwasher - Instructions

Simple, removed screws securing machine in the cabinet, then pull the unit out of the cabinet space about 10 inches. Springs are accessible within this extension. You need strong hands to extend the springs and attach them. Once attached, push machine back in place and re-install the anchor screws. In my situation, only one spring was broken, so the attached side revealed the correct slot to place the hook on the top position, the bottom position has a plastic lead for the spring, and that lead is attached to a rope to the door hinge. Note: Replace BOTH springs, even if only one is broken.

We replaced the rusty with the new ones.

The inside gasket deteriorates over time - However replacement is easy. the main thing you have to remember is after you remove the old gasket, install the new one starting at the middle top of the tub and work your way down both sides. Also, don't push the gasket all the way in...only enough to hold in place. When you close the door the gasket will form a better seal around the door.

Ordered the roller from Parts Select, slid the roller over the little spindle sticking out of the bottom rack and snapped it in place. Job done in less than one minute.

Pull the dishwasher out from underneath the countertop took 2 minutes unscrewed the panel on the side one minute put the connector on one minute screwed the panel back on 1 minute put the dishwasher back underneath the counter two minutes very easy job

Turn off the power at breaker box. Disconnect the power at dishwasher since I needed to pull the unit all the way out of the cabinet to get to screws on the back side for this model. Find and remove the screws to the cover. Remove cover. In my case, the rope on the connector assembly had snapped. I replaced spring and connector identically to functioning side. Did need a pair of pliers to provide enough tension on spring to install. Reconnected cover and power and moved back into the cabinet. Easy repair and my wife wondered why I hadn't done it sooner.

Snapped the rollers on.

Disconnect washer - pull out and turn on it's right side. Remove bottom plate (2 screws). Water intake valve is attached to water line. Disconnect water line. On the other end of the pump is a rubber hose. Disconnect hose by using a pair of pliers to open pipe clamp. Disconnect the electric line by pulling the pronged plug out of the pump. The part is composed of the pump and a metal mounting plate. They are connected by 4 screws. Remove the screws and pull out the back half of the pump. The front of the pump is attached to the washer frame by 2 screws. When removed you will notice an o-ring that forms the seal between the two halves. Remember this when installing the new pump. You will have to take the new pump apart because the whole part will not fit through the frame opening, thus the need to make sure the o-ring is properly seated. You can either install the mounting plate to the frame then attach the pump half or with half of the part in front of the frame and the other half behind the frame connect the two, then attach it to the frame. Reconnect incoming water line using teflon tape and a crescent wrench. Reconnect out-flow line with the pipe clamp and attach the power line. Since you have to take the new pump apart make sure the o-ring is properly seated as it will have a tendency to fall out. Reassemble the rest.

Unscrew all screws on the inside of the dishwasher door. Carefully separate the front panel from the inside panel. Lift out the latch assembly, remove connectors from both sides using needle nose pliers. Reconnect to new assembly and situate back into place. Close front and inside panel, replace all screws, making sure the short and long screws go back to where they came from. Quick easy project to eliminate 2 trips from a repairman, 1 for the diagnosis and 1 to do the work!

My husband was able to slide the dishwasher out, and quickly replace the old connector assembly for the new ones. The old connector assembly had broken at the “rope”. Now the door opens slowly and is as good as new.

Took out old rack. Put in new rack. Done.

No other assembly required.

Had to call have an installer attach a metal strip across granite counter top and they did not have the top mount brackets so I had to order them and finish the install. The dishwasher was installed on the side mounts and they missed the cabinets

When I found the problem to be the check valve I reinstalled the drive motor and water pump, ordered the part I needed,Installed the new check valve, installed the rest of the parts and did a test run which corrected the problem.

Loosened 3 screws and unhooked supply line and electric box and pulled it out.

Took off the broken one and snap on the new one.