Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This kit features a 5-blade plastic evaporator fan blade that rotates CCW and measures 4.5-inches in diameter and has a 3/8-inch-tall shaft. This kit also has a metal compression ring that secures the...
$30.95
In Stock
Order now and your part arrives in 2-3 business days!
This refrigerator defrost thermostat will cut out at 55 degrees F and kick back in when the temperature drops to 35 degrees F. It comes with connectors and the mounting brackets.
$20.95
In Stock
Order now and your part arrives in 2-3 business days!
This condenser fan motor operates in a clockwise fashion. The fan itself has two 1/4 inch spade terminals. It carries 2 watts and 115 volts. This motor NO longer comes with cover for terminals.
The defrost control in your refrigerator acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater, keeping your refrigerator at the appropr...
$84.95
In Stock
Order now and your part arrives in 2-3 business days!
This evaporator fan motor operates in a counter clockwise fashion. This motor's stack is 3/8 of an inch, and the motor has two terminals: one on the right side, and one on the left side. Use this evap...
$50.95
In Stock
Order now and your part arrives in 2-3 business days!
This single outlet valve comes with a gasket, and is intended for refrigerators that have ice makers which make round ice cubes. If the ice maker is still not working properly, the issue could be that...
This part maintains the proper temperature. When the refrigerator reaches the desired temperature, this part interrupts the flow of electricity to the compressor which stops the cooling process.
This replacement ice maker assembly is used on many of GE's refrigerators. This assembly makes round ice cubes, but does not come with a new feeler arm. You will have to re-use the feeler arm from you...
No Longer Available
Questions And Answers for CTF21GBC
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
The temperture control was mounted on the back wall of the refrigerator. One screw and a couple of tabs appeared to be the only attachments. After removing the screw, the freezer control appeared to be an issue since it was also attached to other parts. A little careful pushing revealed that the control knob simply snapped into the cover
... Read more over the thermastat. Once unsnapped the thermastat and it's plastic cover were only attached by the three electricl connections. Pulling them loose off the terminals left the unit free. Simply examining how the old thermastat was mounted in the cover, and replacing it, and then reinstalling it in the frig was as breeze. All was well again.
Moving the frig out and cleaning was the hardest part of this job - lots of dust collected over the 17 years the frig was in place. Once all the cleaning was done, with the frig out and back cover off (10 -12 screws taken off with nutdriver),I plugged the frig in and observed the the problem was a noisy fan motor. The motor is at the very
... Read more back of the frig with easy access to the 3 brackets holding it in place. Pull off the electrical clip. Remove the screw holding the bracket to the frame on the front bracket, leaving the bracket attacked to the fan. The other two screws remove from the fan, leaving the brackets in place. Reverse the procedure when you receive the new part from PartSelect(great company to deal with)!
