CS-330T (09001001 - 09999999) Echo Chainsaw - Overview
Sections of the CS-330T
[Viewing 16 of 16]Keep searches simple, eg. "belt" or "pump".

Trimmer Spark Plug
PartSelect #: PS9263506
Manufacturer #: 15901019830
This Spark Plug Bpm-8y is a silver and white OEM part. Made of steel and ceramic it is individually sold, and is an electrical part. It is installed with a spark plug socket and is rated as Easy to in...
$5.95
In Stock

Trimmer Fuel Filter
PartSelect #: PS11826311
Manufacturer #: A369000480
This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers.
Th...
$5.36
In Stock

Leaf Blower Fuel Tank Vent
PartSelect #: PS9183121
Manufacturer #: A356000031
This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Ma...
$7.63
In Stock

Chainsaw Stud
PartSelect #: PS9237151
Manufacturer #: V224000031
This part is the replacement stud for your chainsaw. It is approximately 1 ¼ inches long and is black in color. The stud secures the chain bar to the chainsaw. It the stud is damaged or missing, it ca...
$5.95
In Stock

Trimmer Clip
PartSelect #: PS9261895
Manufacturer #: 13201309820
This genuine fuel clip is a silver, metal, individually sold part. It can be installed with pliers and is rated as Easy to install by customers.
This part attaches to the fuel filter to secure the fu...
$5.19
In Stock

Trimmer Fuel Line Clip
PartSelect #: PS10053748
Manufacturer #: V490001230
Used in over 150 models of outdoor power equipment, this clip is commonly used to clip fuel lines or other hoses/tubes in place. It is sold individually, not as part of a kit or assembly, made of meta...
$5.95
In Stock

Trimmer Nut
PartSelect #: PS9148697
Manufacturer #: 90050000005
This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to se...
$5.95
In Stock
Questions And Answers for CS-330T
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
worn out paddles and scrapper blade
I followed the instructions on Youtube, but I used an Impact drill and ratchet set. The hardest part is assembling the screw on the lower part of the paddle. It helps if you have your snow blower against a wall or something else so that it can not move b/c you will need some strength to push the screw threw the pre-drilled hole to the 10
... Read more
mm nut. I used a vise grip to hold the nut do to the lack of space and with my impact driver started to thread the screw to the nut. This part took about 1 min on one side and 10 minutes on the other side. I guess I got lucky the first time. Changing the scraper blade took about 4 minutes start to finish. It will help if you have needle nose pliers to remove and reattach the spring on each side. The instruction on you tube were very helpful. Hope you find this information helpful.
Read less
Parts Used:
-
Sam from GAITHERSBURG, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
2 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!