CL0501510 Powermate Compressor - Overview
Sections of the CL0501510
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Air Compressor Regulator Repair Kit
PartSelect #: PS9877209
Manufacturer #: 105-0004
$55.32
In Stock
Air Compressor Piston Cylinder Assembly
PartSelect #: PS9868931
Manufacturer #: 048-0074
$239.75
In Stock
Questions And Answers for CL0501510
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
hubcap fell off my coleman air compressor
repair didn't happen the part was the wrong size so i wasted $20 and my time because the part was on back order (which the website did not show) Will never use you service again, complete waste of time and money
Parts Used:
-
Richard from AUBURN, WA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Compressor pump not filling ballast tank
1.) Disassemble the pump/motor assembly located on the top of the unit:
a.) Remove outermost plastic shroud. You will need a nut driver with an extension to get to one hex screw - a good Xcelite set will do.
b.) Remove inner plastic shroud with filter sponge. If filter sponge is clogged, replace it.
c.) With plastic s ... Read more hrouds removed, begin disassembling the metal pump components. Start by removing the four screws around the dome cover.
d.) Remove last two screws holding valve plate to piston housing case and remove.
e.) Remove the piston cylinder from the piston housing by lifting up.
f.) Loosen the clamp screw holding the piston rod to the bearing. Pull the piston away from the bearing - you might have to wiggle or pry on it a bit to slip it off. If you have to pry it off, pry only the piston rod itself - take care not to damage the bearing.
2.) Inspect gaskets for wear or damage - replace as necessary. For Piston and Cylinder assembly kit purchased from Parts Select, a gasket mated between the cylinder and valve plate will be included.
3.) Inspect valve plate for bent valve reeds or for debris caught between the valve reeds and the plate. Remove any material found and replace valve reeds as necessary.
4.) Reassemble by following instructions from step 1 in reverse. Mind the torque specifications - images are available online for these torque specifications.
a.) Remove outermost plastic shroud. You will need a nut driver with an extension to get to one hex screw - a good Xcelite set will do.
b.) Remove inner plastic shroud with filter sponge. If filter sponge is clogged, replace it.
c.) With plastic s ... Read more hrouds removed, begin disassembling the metal pump components. Start by removing the four screws around the dome cover.
d.) Remove last two screws holding valve plate to piston housing case and remove.
e.) Remove the piston cylinder from the piston housing by lifting up.
f.) Loosen the clamp screw holding the piston rod to the bearing. Pull the piston away from the bearing - you might have to wiggle or pry on it a bit to slip it off. If you have to pry it off, pry only the piston rod itself - take care not to damage the bearing.
2.) Inspect gaskets for wear or damage - replace as necessary. For Piston and Cylinder assembly kit purchased from Parts Select, a gasket mated between the cylinder and valve plate will be included.
3.) Inspect valve plate for bent valve reeds or for debris caught between the valve reeds and the plate. Remove any material found and replace valve reeds as necessary.
4.) Reassemble by following instructions from step 1 in reverse. Mind the torque specifications - images are available online for these torque specifications.
Read less
Parts Used:
-
Timothy from Chandler, AZ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
pressure switch went out
Out with the old in with the new. came with instructions which made it a breeze..
Parts Used:
-
daniel from LA PORTE, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!