CGLMV168KS001 General Electric Range - Instructions

Turned out the issue was easily solved by replacing a single, inexpensive fuse.

First off, UNPLUG THE MICROWAVE.

The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.

I had no idea what to expect. I was tired to see this turn table not moving. I removed the 7 screws at the bottom of the microwave that I thought was hiding the turn table mechanism. Bingo! I removed the 2 screws holding the motor and check if the power was coming to the motor and it was. The motor was cooked.
I decided to change the filter since I was working on this. When I received it, and proceeded to change it, I found out that there was no filter. Finding the right position was a bit tricky. The most difficult part was to remove the front vent grille.

Don’t be shy, try it! Make sure, to disconnect the power when changing the filter.

First I unplugged the microwave. :) Then, I removed the 6 screws found underneath the microwave, which allowed the bottom piece to hang down so I could see the turntable motor. I took the two screws out holding the motor in place and pulled the electric connectors off the motor terminals. Then I got the new part from PartSelect.com, replaced the electrical commectors, fit the motor back into the slot it came from (cause the pin has to be seated up in the hole) and replaced the 2 screws holding in the motor. Then I put the bottom metal piece back up and put the 6 screws back in. It was really easy - and I'm a chick! ;)

Had to take unit off wall and disassemble the main casing.then disconnected the wires from the magnetron.took the mounting nuts off but wasn't able to remove the magnetron until I loosened the transformer out of the way .Then it came out easy.Installed the magnetron ,tightened the nuts,installed the transformer back in, connected the the wires back on and installed the casing on ,screwed the screws and got help to install the unit to the wall again.....Tested the unit before putting back on the wall to make sure it heated....The parts were exac same type and wasn't too hard to do...

Unscrewed bottom plate of microwave and two screws that secured motor. Disconnect wires. Reversed process when installing new motor. Couldn't have been easier.

The tray drive motor arrived quickly. I opened the package and made sure the correct motor arrived. I shut off the power to the microwave/exhaust hood. Then I grabbed a screwdriver and dropped 5 screws from the bottom of the microwave. I then removed 2 more screws that hold the motor in place. Unplugged the 21 volt power clips. Placed the new motor in position and replaced the screws and attatched the power clips. I then placed the bottom pan in position and replaced the 5 screws that hold it to the bottom of the microwave. Turned the microwave on and it worked properly! The total cost was $40 and I probably saved more than a hundred dollars on a service call. What a happy ending and it took about 5 minutes to perform the repair! Thanks PartSelect. You are the best!

I had to pop off the facing on the microwave on the inside and then on the outside. On the inside, I used a kitchen knife to carefully pop off the facing. I found the screws that were holding the old handle on. I had to pop the back of the microwave door off to gain access to the other screws for the handles. The outer screws had to be put in place first, making sure that the glass did not slip. The facing needed to be popped back on before the inner screws were tightened. I tightened the inner screws and then popped the facing back on. The thing that took me the longest was figuring out how to pop the facing off and lining up the screws in the handles correctly.

Unplugged the microwave first, then removed the screws that hold the cover in place. This gives easy access to the socket. Remove the screws that hold the socket in, unplug old socket, replace with new one and you are back in the light again.

There are 4 thermostats (aka TCO = Thermal Cut Out) in the GE JVM1440BH04
The schematic is under the cover in a black envelope to the top left of the unit if you face the door.

Check the fuse first. You can remove the front grate, then the numpad on the right. The fuse is right behind it. It's a 250V 20A Class F fuse.

There are four (4) TCOs or Thermal Cut Out thermostats in this puppy:

1) There is a thermostat behind the button panel to the left, facing down. If blown, it breaks the power coming into the unit and will cause a no power situation.

2) There is another TCO or thermostat near the top lamp, to the left, in a small cavity. That one also breaks power to the unit and will cause a no power situation. It's a 100 C / 0 C thermostat. This was the one that blew on me after I left the stove running (for heating in a black-out) under the microwave.


"Cavity TCO" or "Thermostat" part number 61 on the schematics, part number PS239319


3) There is yet another power-breaking TCO or thermostat in the cavity behind the fan that cools the microwave coils. You have to remove the sheet metal on the right of the microwave to access it. This one also breaks power and will cause a no power situation.

1), 2) and 3) should test out to be 0 Ohms with a resistance meter (Digital Multimeter) if working correctly.

4) There is a thermostat which normally does not let current through it. It is mounted in a vertical position to the back wall behind the front panel on the right. This one is used for the sensor reheat function apparently and will close when the temperature in the microwave reaches approx. 60 C.

4) should have infinite resistance with a resistance meter under normal circumstances.

Over the range microwave. Replaced magnetron. Completely disassemble the case top and bottom.
Remove screws from bottom of HV transformer. Magnetron will not clear without this removal.

Remove nuts with socket from top of Magnetron. Remove thermo unit from old magnetron and attach it to new. Replace and bolt down Mag. Replace and screw in HV transformer. Make sure all wires are reconnected.

Put it back up on the wall. Took about three hours from taking it down from wall and putting it back up.

1. remove microwave from wall
2. remove cover (many screws)
3. remove nuts holding magnetron in place (4)
4. remove magnetron (this is a pain due to the plastic molding used to direct cooling air through the magnetron
5. get new magnetron in place (this was even more fun to find the right angles to tilt to get the magnetron to fit
6. re-tighten the 4 nuts on the magentron
7. put the cover back on
8. put the unit back on the wall.

bonus repair: the display flickered while the magnetron was on (cooking ) prior to the magnetron dying. found a ribbon cable on the control board to the display with an aluminum foil shield that had peeled off (adhesive failure). re-installing the aluminum shield with packaging tape, and the display no longer flickers

The old fuse is perfectly good. The new ones arrived within a day.

Philips head screwdriver to remove 2 screws holding plastic grill above microwave door in place. Old Filter lifts out slide new filter in. It rests on an angle. Re insert Grill (careful that plastic tabs slide into proper slots). Tighten SCrews

First, I waste $65 by calling some "REPAIR" service. They showed at home and charge me that just to tell me
Second, I researched on the web and ordered a part, which was not the issue. I waste abnother $72
Third, I found Part-Select and got the right answer: the Diode was the problem. Ordered the part form Part-Select and it FIxed it !!!

Note: I did not buy a new microwave because this one is mounted on the wall and it will cost me +$800 just the lowest price.

1. turned off electricity -- unplugged the unit 2. removed 3 screws on top of top vent, removed vent screen then I located the little white cylindrical fuse and popped it out with a table knife. Then I popped in the new fuse. Replaced the vent screen and screws -- plugged in the appliance and it is working again.