Parts That Fix General Electric Refrigerator CFE29TSDCSS Fridge too warm
Fridge too warm is a commonly reported symptom for the CFE29TSDCSS General Electric Refrigerator, and we have put together a full guide
... Read more
on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your CFE29TSDCSS General Electric Refrigerator that will fix Fridge too warm.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Read less
Fridge too warm is a commonly reported symptom for the CFE29TSDCSS General Electric Refrigerator, and we have put together a full guide on how to fix this.
This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your CFE29TSDCSS General Electric Refrigerator that will fix Fridge too warm.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Fixes Symptom 76% of time
This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too cold, or not defrosting properly, then there may be a problem with your sensor. The temperature sensor can break from material fatigue or through normal use, and should be replaced. It is attached to the evaporator and control housing in your appliance. It measures approximately 1.25 inches long with 18 inch wire leads, and is constructed out of plastic. This part comes in white, beige. It includes the sensor, with wire leads.
$
28.95
In Stock
PartSelect Number PS304103
Manufacturer Part Number WR55X10025
Replacing your General Electric Refrigerator Refrigerator Temperature Sensor
Customer Repair Stories
refrigerator was getting too cold
I removed the old temperature sensor by cutting the wires. I attached the wires of the new sensor with wire nuts and mounted it in the same bracket.
-
Larry from Menomonie, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
149 of 215 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
my refigerator was warm but the freezer was cold and working correcttly
I went to a GE repair center to explain my problem, the service center reccomended that I have a techinician come out o look at it. $75.00 for the visit and what ever labor and materials wuld cost.
I went on line to see if there were others having this same problem and found that there were many with the same problem.
... Read more
/>After reading some of the ways that people found out what was wrong ...it became a matter of three components, the timer, heater or thermostat.
I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
I went on line to see if there were others having this same problem and found that there were many with the same problem.
I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
Read less
-
michele from North Smithfield, RI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
297 of 381 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 17% of time
The Refrigerator Evaporator Fan Motor is an OEM replacement part for some GE refrigerators. It is responsible for circulating air over the evaporator coils, which are responsible for cooling the refrigerator's interior. Causes of a bad evaporator fan motor can include bearing failure, motor burnout due to overheating, or electrical issues. A malfunctioning fan motor can lead to temperature fluctuations, frost buildup, and ultimately, reduced cooling efficiency.
$
75.95
In Stock
PartSelect Number PS12172983
Manufacturer Part Number WR60X26866
Customer Repair Stories
+-LOWER DRAWER ICED OVER IN BACK AND CONTENTS FROZEN UPPER STORES NOT COLD ENOUGH
REMOVE LOWER DRAWERS, SHELF AND BACK EVAPORATOR COVER AND REPLACE SIEZED EVAPORATOR BLOWER MOTOR.
-
CHARLES from FAYETTEVILLE, OH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
10 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The refrigerator was too warm. The drawers where vegetables and fruits are kept were being frozen. The vents blowing cool air into bins were iced up.
Took the drawers out of fridge and unscrewed the support rails for drawers and unscrewed inside back wall of fridge. Removed cover on blower fan ~ unplugged fan. This took 45 mins. Left refrigerator unplugged and let thaw out. Replaced with new fan 5 days later. Plugged in new fan. Then
Plugged in refrigerator to make sure it would ... Read more work. After 15 minutes, unplugged fridge and put rails and drawers back. Total time 45 minutes. Plugged refrigerator back in and let run 24 hours.
It took 5 days to get part due to snow storm delaying delivery. It works perfectly. Our GE will be 10 years old in August.
Plugged in refrigerator to make sure it would ... Read more work. After 15 minutes, unplugged fridge and put rails and drawers back. Total time 45 minutes. Plugged refrigerator back in and let run 24 hours.
It took 5 days to get part due to snow storm delaying delivery. It works perfectly. Our GE will be 10 years old in August.
Read less
-
Eunice from POWELL, WY
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 2% of time
$
37.95
In Stock
PartSelect Number PS8688283
Manufacturer Part Number WR50X10108
Fixes Symptom 2% of time
The evaporator fan motor circulates air through the fresh food compartment for efficient cooling.
$
52.42
In Stock
PartSelect Number PS12727431
Manufacturer Part Number WR60X25858
Customer Repair Stories
Top of frig would not cool. Now temperature display in in sync with the 37 degree setting I adjusted it to.
removed frig bottom long drawer, removed the 2 narrower drawers above that. removed 2 plastic plates above the long drawer and unplugged pigtail. removed lower drawer slides and the back coil cover. removed small shroud that contained the fan pigtail and then removed the fan and replaced with the new one. fixed cooling issue and took 10
... Read more
minutes from start to finish.
Read less
-
david from SMYRNA, GA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
17 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
$
194.82
In Stock
PartSelect Number PS17875680
Manufacturer Part Number WR55X46805
Customer Repair Stories
After power outage, my refrigerator would not cool after power came back.
After looking up what might be the problem, I ordered a new control
board. It was extremely easy to replace. Unfortunately it was not operational. I had to replace my refrigerator. The return process was very easy and my refund was processed quickly.
board. It was extremely easy to replace. Unfortunately it was not operational. I had to replace my refrigerator. The return process was very easy and my refund was processed quickly.
-
Denise from Finleyville, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator would warm up while freezer got colder
Repair man thought it was the control board and an issue with a relay on the board. Purchased the new board but found out the board was fine, and it was the recirculating fan that would go out intermediately.
Tried ordering that part from Part Select since they have been great, but GE discontinued the part and their was not a r ... Read more eplacement available. After much research, found the new replacement part number and ordered that, it went in quickly and for now seems to have solved the problem.
Tried ordering that part from Part Select since they have been great, but GE discontinued the part and their was not a r ... Read more eplacement available. After much research, found the new replacement part number and ordered that, it went in quickly and for now seems to have solved the problem.
Read less
-
Richard from CHEBOYGAN, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
$
48.95
In Stock
PartSelect Number PS6883666
Manufacturer Part Number WR51X10132
Fixes Symptom 1% of time
$
99.86
In Stock
PartSelect Number PS8690738
Manufacturer Part Number WR60X10358
Customer Repair Stories
Condenser overheating prevented refrigerator from cooling properly
Unplug the fridge. Open the panel on the rear bottom of the fridge. Find the fan in the middle, facing the condenser on the left and coils on the right. Push the tab down, on the bottom of the plastic translucent bracket holding the fan, and pull the fan halfway out. Note where the wires run, so you when you replace the fan, it fits prope
... Read more
rly. Also note which side of the fan faces the condenser. Unplug the two connectors, and pull the fan the rest of the way out. One connector requires you to squeeze the sides. Reverse these directions to put the new fan in. Plug the fridge in to verify your installation. The fan will not start immediately, but will start within a minute. Replace the rear panel.
Read less
-
Richard from Bothell, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refridge wasent cooling
Very simply remove the dust cover you will see fan in front of condensor it simply slides out unplug the two plugs and then take the time to clean dust with vacum (I used air compressor to blow dust out) reinstall takes about 15 mins total start to finish.
-
Jeff from KINGSTON, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
14 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
Upgrade your refrigerator by installing the GE Refrigerator Fan Motor Boot. This piece is key in keeping your fridge running smoothly as it secures the fan motor behind the evaporator cover. Allow your stored food to maintain their freshness and cold temperature by optimizing the function of your appliance. Please remember to protect your hands with work gloves during installation and always disconnect the refrigerator from its power source as a safety precaution. This product is from GE, a trusted name in appliances. Enhance your refrigerator's performance today with the GE Refrigerator Fan Motor Boot.
$
22.95
In Stock
PartSelect Number PS12228022
Manufacturer Part Number WR24X27948
Fixes Symptom 1% of time
$
33.95
In Stock
PartSelect Number PS16554876
Manufacturer Part Number WR23X37285
Customer Repair Stories
The refrigirator light would not come on.
Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.
-
Jania from Novato, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
25 of 40 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Sticking Light Switch
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the c
... Read more
atch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.
Read less
-
Jonathan from Lilburn, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
120 of 166 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!