AA4212 Speed Queen Washer - Overview
Sections of the AA4212
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Retaining Ring
PartSelect #: PS11740487
Manufacturer #: WP23748
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place o...
$12.52
In Stock
Adjustable Leveling Leg
PartSelect #: PS2021026
Manufacturer #: 22003428
If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs ...
$14.96
In Stock
Washer Inlet Hose Washer
PartSelect #: PS11757437
Manufacturer #: WPY013783
This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to create a watertight seal...
$3.95
In Stock
Drive Bell and Seal Kit
PartSelect #: PS2174335
Manufacturer #: R9900189
This washing machine drive bell and seal kit comes with a seal, a plug, a shoulder screw, a drive bell, and some grease.
No Longer Available
Washer Nut
PartSelect #: PS11741865
Manufacturer #: WP358160
This serrated nut is used for many clothes dryers. It is less than an inch long, and is made entirely of metal.
$7.95
Special Order
Dryer Nut
PartSelect #: PS11748944
Manufacturer #: WPW10139757
Sold individually. This nut is for dryers.
Follow appropriate safety practices when installing the nut.
$7.95
On Order
Screw
PartSelect #: PS2040891
Manufacturer #: 40038901
Sold individually. 1/4-20
No Longer Available
Questions And Answers for AA4212
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the AA4212
[Viewing 4 of 4]Noisy
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
grease in washer
remove agitator then remove center bolt from hub, match bolt with longer bolt so that gear puller will work. install bolt and gear puller and twist top of gear puller until hub is removed. remove old seal ,use sand cloth or emery cloth to remove all deposits from shoulder. make it shinny, use some dawn dishwashing soap to line the inside
... Read more
of the new seal at the bottom and slide into place.take a piece of 2" PVC about 4" long and slide over the top of the seal and tap with a rubber hammer until seal is seated firmly on shoulder. look to see that there are no gaps with a inspection mirror or a make-up mirror.If their are no gaps ,install the hub and tap on the new hub with the rubber hammer. the hub will not seat all the way down so use the old bolt to pull it down, now take out the old bolt and install the new one, this is because the new one has lock tite on it ,your done!
Read less
Parts Used:
-
Jan from Denver, CO
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Socket set
6 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Threads on old legs had been damaged in moving to new location.
Removed the damaged legs, replaced with parts from this site and leveled the washer .
Parts Used:
-
Wayne from SEDONA, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Wrench (Adjustable)
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leg was mssing after move into new home.
Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if nec
... Read more
essary.
Read less
Parts Used:
-
Matthew from The Woodlands, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!