91136665690 Kenmore Range - Instructions

The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)

Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two hex head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.

Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.

first I removed all the srews from the burners that hold the glass cooktop. I then disconected the two wires from the damaged gas valves and replaced them all four with the new ones. After that I put it all togehter and work just fine and celebrated with a good cold beer.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I have a GE Profile Gas Range that was installed by the builder in 1997. The porcelain bowl under the grate had chipped on all the elements. I replaced them easily..quickly...and was very cost effective...thanks for the great service...great site to order from. AC

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

Very easy once I got the right parts - when I ordered I didn't realize that the center holes were what determined whether I needed "small" or "medium/large"...I was going by the exterior dimensions I returned 3 of the 4 I ordered and re-ordered the right size. My wife ended up replacing the rest of them herself after watching me do the one that did fit. Looks like a new stove!

replaced lights in refrigirator and freezer

I replaced the igniter under the knob.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Shut of electric supply. Remove knobs and open top cover of cook top by removing two screws near each burner and replace switch.

REMOVED 5 PHILLIPS SCREWS
REMOVED BROKEN RT CAP
INSTALLED NEW END CAP
REINSTALLED THE SCREWS
PROJECT COMPLETE

Easy

The top is all glass so I took my time. There was about 12 screws and double sided tape. A lock washer holding the igniter on. It also gave me a chance to clean the hard to get to places. Your price was almost half of what a suppier here and getting it would have been 2 weeks compared to your 48 hours to my door. Thanks again