91133386890 Kenmore Cooktop - Overview
Sections of the 91133386890
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Large Burner Drip Bowl
PartSelect #: PS244310
Manufacturer #: WB31K5079
This is a replacement drip bowl for your range or oven. The drip bowl sits beneath the burner element and collects any drips or spills. This drip bowl is 8 inches in diameter and is used to replace th...
No Longer Available
Medium Burner Drip Bowl
PartSelect #: PS244311
Manufacturer #: WB31K5080
This burner drip bowl is sold individually. It is white on the top side, and black underneath.
$42.95
In Stock
Screw
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$13.95
In Stock
Small Burner Drip Bowl
PartSelect #: PS244312
Manufacturer #: WB31K5081
This burner drip bowl is sold individually. It is white on the top side, and black underneath.
$36.95
In Stock
Gas Pressure Regulator
PartSelect #: PS2337785
Manufacturer #: WB19T10078
This comes set from the manufacturer for Natural Gas. It also includes the conversion to Liquid Propane.
This valve automatically cuts off the flow of gas at a certain pressure.
$49.95
In Stock
Ignition Spark Switch - Rear Burners
PartSelect #: PS236639
Manufacturer #: WB24K5083
Upgrade your GE cooktop with this Ignition Spark Switch for Rear Burners and feel a new level of efficiency in your cooking! This crucial appliance accessory provides the needed spark for your burner ...
$36.95
In Stock
Ignition Valve Switch - Front Burners
PartSelect #: PS236635
Manufacturer #: WB24K5078
Enhance the performance of your GE cooktop with this Ignition Valve Switch. Exclusively designed for front burners, it utilizes a spark ignition system to effectively ignite the burner, ensuring optim...
$47.95
Special Order
Liquid Propane Orifice Spud
PartSelect #: PS240918
Manufacturer #: WB28K5087
This orifice spud changes the burner from natural gas, to liquid propane. This orifice is sold individually.
No Longer Available
Spark Module - 120V 60Hz
PartSelect #: PS231335
Manufacturer #: WB13K5079
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$96.97
Special Order
Questions And Answers for 91133386890
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 91133386890
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The porcelain had chipped on the burner bowls
Removed the two screws holding the porcelain burner bowl. Disconected the electric igniter by removing the "w" clip on the underside of the bowl. Then disconnected the igniter from the electric supply cord. Reverse these directions using the new urner bowl.
Really easy.
Really easy.
Parts Used:
-
Paula from Seal Beach, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
14 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner bowl worn out from cleaning
Pulled off burner grates, burner, unscrewed burner bowl, removed clip from igniter and wire, then put it all back together. Was very easy, and the stove looks like new again.
PartSelect is very good with amazing shipment times. The kjpart arrived much sooner than expected.
PartSelect is very good with amazing shipment times. The kjpart arrived much sooner than expected.
Parts Used:
-
Leon from Lancaster, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner bowl mounting holes out of alignment
No way to adjust mixer tube assembly so the mounting holes will line up with the holes in the burner bowl. Mounting
holes in bowl should be slotted to prevent future problems.
Had to finally bend the mixer tube mounting bracket enough to get one bowl on. It also made the procelin break
on that bowl because the screw put t ... Read more o much pressure on the side of the hole.
Igighter mounting hole out of position just enough to prevent the burner head from sliding over it and sitting on
the mixer tube correctly.
I solved this problem by fileing the opening slot for the igniter. Even with the igniters being just a little out of
alignment from the original position they still light well.
I did not get new gaskets for the burner bowl but would reccommend that you get them.
holes in bowl should be slotted to prevent future problems.
Had to finally bend the mixer tube mounting bracket enough to get one bowl on. It also made the procelin break
on that bowl because the screw put t ... Read more o much pressure on the side of the hole.
Igighter mounting hole out of position just enough to prevent the burner head from sliding over it and sitting on
the mixer tube correctly.
I solved this problem by fileing the opening slot for the igniter. Even with the igniters being just a little out of
alignment from the original position they still light well.
I did not get new gaskets for the burner bowl but would reccommend that you get them.
Read less
Parts Used:
-
Keith from Frisco, TX
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!