Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a w...
$44.83
In Stock
Order within the next 5 hrs and your part ships today!
This drain pump is for washers. Drain pump removes water from the washer during the drain portion of the cycle. Unplug the washer before installing this part. Wear work gloves to protect your hands.
$174.98
In Stock
Order within the next 5 hrs and your part ships today!
This is a drain hose assembly for top-load models of LG washing machines. This hose specifically is used to allow water to drain from the tub to the drain pump of the washer. This hose is made of plas...
$40.88
In Stock
Order within the next 5 hrs and your part ships today!
Introducing the customized screw designed exclusively for LG washers. Manufactured with safety and efficiency in mind, installation is straightforward when you adhere to correct safety regulations. Sh...
$20.67
In Stock
Order within the next 5 hrs and your part ships today!
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pum...
$44.04
In Stock
Order within the next 5 hrs and your part ships today!
HOUSING ASSEMBLY,CLUTCH
This drive shaft and shifter assembly (part number AEN73131403) is for washers.
Drive shaft and shifter assembly AEN73131403 connects the motor with the washplate, and shif...
Ensure smooth functioning of your LG washer with our genuine LG Washer Shifter Coupling. This vital part helps your washer shift seamlessly between agitation and spin mode, enhancing the efficiency of...
$38.99
In Stock
Order within the next 5 hrs and your part ships today!
Introducing the LG Washer Washplate Pulsator Assembly, a genuine OEM replacement part designed for select models of LG washing machines. This pulsator assembly is an integral component, designed to ef...
$171.45
In Stock
Order within the next 5 hrs and your part ships today!
This genuine LG STATOR ASSEMBLY is designed to perfectly fit your washer and ensure it operates at optimal efficiency. This washer drive motor comes with a sensor and plays a crucial role in rotating ...
$263.30
In Stock
Order within the next 5 hrs and your part ships today!
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read morepplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
Removed the inner tub laid the washer on its side with a blanket under it and Removed the assembly then the shaft assembly. Installed the new assembly and re assembled the rest of the washer (top and bottom) and plugged it in. Works great. TIP: you will need a big socket set for the tub retaining nut.
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new
... Read more leg was a breeze.
