28CH77-0036-E1 Briggs and Stratton Engine - Overview
Sections of the 28CH77-0036-E1
[Viewing 6 of 6]-
Air Cleaner Blower Housing Exhaust System
-
Alternator Controls Electric Starter Governor Spring Ignition
-
Camshaft Crankshaft Cylinder Engine Sump Gasket Set - Engine Pistons Rings Connecting Rod
-
Carburetor Fuel Supply Kit - Carburetor Overhaul
-
Cylinder Head Gasket Set - Valve Lubrication Valves
-
Flywheel Rewind Starter
Keep searches simple, eg. "belt" or "pump".
Engine Ratchet Pawl
PartSelect #: PS8942598
Manufacturer #: 281505S
The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will...
$3.99
In Stock
Engine Oil Seal
PartSelect #: PS9151828
Manufacturer #: 795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty...
$7.88
In Stock
Gasket--Rocker Cover
PartSelect #: PS8941245
Manufacturer #: 272475S
This OEM Gasket Rocker Cover, which can also be called the Valve Cover Gasket, is used to provide a seal between the valve cover and engine. This is a gray-colored part, measuring 5 1/2 x 4 Inch, and ...
No Longer Available
Engine Oil Seal
PartSelect #: PS9277860
Manufacturer #: 391086S
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "M...
$6.59
In Stock
Engine Exhaust Gasket
PartSelect #: PS9294808
Manufacturer #: 692236
This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in...
$5.71
In Stock
Engine O-Ring
PartSelect #: PS9294749
Manufacturer #: 691917
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and ma...
$4.99
Special Order
Questions And Answers for 28CH77-0036-E1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Screw can out of the carburator throttle baffel and stuck in the exhaust valve
No compression. Removed the cylinder head. freed the screw, checked the valve to see if it still sealed. Turned the head over with the valves in it, install a spark plug, fill the head dome with gas and see if any leeks out over a 2 hr period. If not you are good to go. Reinstalled every thing with new gaskets and a new carburetor screw.
... Read more
Set the valves to spec. Complete the rebuild and there you have it. Rebuild the carburetor while you have it apart. This motor runs great !!!
Read less
Parts Used:
-
FRANK from EASTANOLLEE, GA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set, Wrench set
9 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stopped running. Turned to be a bent intake push rod and broken rocker arm
Removed head. Replaced both rocker arms, intake pus rod, push rod guide exhaust and head gaskets. Torqued head in 3 stages to 216 in/lbs. gapped intake to .004 and exhaust to .006 at TDC
Added oil and gas. Now running great
If you need to replace push rods use steel (exhaust) they are the same length
The engine ... Read more was a Briggs & Stratton 217802 0113 E10604 (2006 year date code)
I used the following
796189 gasket
272475S gasket
697494 push rod
690822 push rod guide
691751 rocker arms
Added oil and gas. Now running great
If you need to replace push rods use steel (exhaust) they are the same length
The engine ... Read more was a Briggs & Stratton 217802 0113 E10604 (2006 year date code)
I used the following
796189 gasket
272475S gasket
697494 push rod
690822 push rod guide
691751 rocker arms
Read less
Parts Used:
-
Rene from COVINGTON, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Socket set, Wrench set
6 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas leaking from tube breather
First I opened the top of the mower to expose the housing cover. Secondly I removed the four housing bolts to remove the housing cover from the mower. Next I removed the tube breather and installed the new tube breather and replaced the housing cover with the four bolts previously removed and closed the top of the mower. I filled the mow
... Read more
er with gas to check for leaks which weren't any leaks. I proceeded to mow the lawn with ease.
Read less
Parts Used:
-
Emanuel from FERRIDAY, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
7 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!