205- - Overview
Models starting with 205-
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Engine Filter
PartSelect #: PS9275043
Manufacturer #: 298090S
This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out ...
$4.99
In Stock
Engine Governor Gear
PartSelect #: PS9151758
Manufacturer #: 793338
Ensure smooth and balanced operation of your Briggs and Stratton engine with this exceptional Gear Governor. It's intricately designed to maintain control over the speed of the engine, contributing to...
$30.58
Special Order
Lawn Mower Washer
PartSelect #: PS9311087
Manufacturer #: 936-0119
This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent ...
$4.95
In Stock
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mistreated Briggs & Stratton 206 CC Engine on MTD Chipper
Removed tank and drained old gas.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Read less
Parts Used:
-
Dana from HAMMOND, IN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
7 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad governor
Look on YouTube for video's on how to replace a Briggs governor. There are several there. My favorite, with best explanation, is, "Easily Replace Briggs Governor Gear (V-Twin Intek Engine) with Taryl". https://www.youtube.com/watch?v=wn3eanGxSEA&t=152s.
Taryl (probably not his real name) does a very good job of showing step-by- ... Read more step the whole procedure, along with some additional hints/tricks/techniques of value.
Not including oil and filter, I spent less than $50 for a new governor, gasket, and drive shaft seal. That's all that is really necessary to replace is those three parts. That is, unless pieces of the old governor tore up a gear, valve, or something else. Inspect everything! {I was lucky and only the governor was destroyed}
One word of note. Be sure to clean out all of the debris from the blown governor. Be sure to remove the spark plugs and carefully rotate the drive shaft while looking for nooks-and-crannies where debris can hide. I tried to use a magnet to help, but it didn't help much, even though the block is aluminum.
Good luck.
Taryl (probably not his real name) does a very good job of showing step-by- ... Read more step the whole procedure, along with some additional hints/tricks/techniques of value.
Not including oil and filter, I spent less than $50 for a new governor, gasket, and drive shaft seal. That's all that is really necessary to replace is those three parts. That is, unless pieces of the old governor tore up a gear, valve, or something else. Inspect everything! {I was lucky and only the governor was destroyed}
One word of note. Be sure to clean out all of the debris from the blown governor. Be sure to remove the spark plugs and carefully rotate the drive shaft while looking for nooks-and-crannies where debris can hide. I tried to use a magnet to help, but it didn't help much, even though the block is aluminum.
Good luck.
Read less
Parts Used:
-
John from BROOKVILLE, IN
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Socket set, Wrench set
8 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!