20076 Toro Lawn Mower - Overview
Models starting with 20076
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Lawn Mower Stepped Washer
PartSelect #: PS9048394
Manufacturer #: 614426
The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. I...
$3.99
In Stock
Lawn Mower Mulching Blade (22-In)
PartSelect #: PS11804777
Manufacturer #: 131-4547-03
This is a genuine OEM replacement blade for use on Lawn Mowers. If the blade is too dull it will tear the grass instead of an even cut. A bent or damaged blade can cause serious damage or injuries. Yo...
$20.80
In Stock
Engine Screw
PartSelect #: PS9053486
Manufacturer #: 650898A
This screw, also known as a shoulder bolt, is a genuine OEM replacement part for your lawn mower. This metal screw holds the starter grille in place against the rewing starter on your lawn mower. It r...
$5.15
In Stock
Lawn Mower Locking Ring Clip
PartSelect #: PS9052921
Manufacturer #: 65-2720
This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secure...
$5.95
In Stock
Lawn Mower Shoulder Bolt
PartSelect #: PS9046634
Manufacturer #: 614650
The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket...
$4.99
In Stock
Lawn Mower Compression Spring
PartSelect #: PS8961286
Manufacturer #: 39-9650
This is a compression spring that is used within various models of lawn mowers and is used to provide stability and extra control to the user during the operation of the equipment. This spring works i...
$4.17
Special Order
Bowl Gasket Tecumseh
PartSelect #: PS9958948
Manufacturer #: 49-841
This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated...
No Longer Available
Exact Part matches for your search term
[Viewing 2 of 2]
SCREW, BREAKER STRIP
This part number matches the current model number 20076
PartSelect #: PS2016321
Manufacturer #: 20076
No Longer Available
Housing
This part number matches the current model number 20076
PartSelect #: PS10337395
Manufacturer #: 20076
$242.74
Special Order
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Torsion spring broken
I pryed the apart the torsion spring lever from the handle with a large screw driver. It wasn't easy putting it back, but it worked
Parts Used:
-
Henry from ORLAND PARK, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
3 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost PartSelect Number PS9053486; Tecumseh 650898A screw
I lost two of the screws that hold the plastic Lawn Boy cowling to the Tecumseh lv195ea engine. I just replaced the lost screws with the newly ordered screws.
Parts Used:
-
Steven from FAIRVIEW, TN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
3 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Read less
Parts Used:
-
Ray from YARDLEY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
3 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!