20009 - Overview
Models starting with 20009
Click on the best match to narrow your results.
- 20009 (270000001-270999999 - 2007) Toro Lawn Mower (Lawn Mower)
- 20009 (260000001-260999999 - 2006) Toro Lawn Mower (Lawn Mower)
- 20009 (250000001-250999999 - 2005) Toro Lawn Mower (Lawn Mower)
- 20009 (240000001-240999999 - 2004) Toro Lawn Mower (Lawn Mower)
- 20009 (230000001-230999999 - 2003) Toro Lawn Mower (Lawn Mower)
- 20009 (220000001-220999999 - 2002) Toro Lawn Mower (Lawn Mower)
- 2000902 (CS40L210) Greenworks Chainsaw
Keep searches simple, eg. "belt" or "pump".
Lawn Mower Mulching Blade (22-In)
PartSelect #: PS11804777
Manufacturer #: 131-4547-03
This is a genuine OEM replacement blade for use on Lawn Mowers. If the blade is too dull it will tear the grass instead of an even cut. A bent or damaged blade can cause serious damage or injuries. Yo...
$20.80
In Stock
Engine Screw
PartSelect #: PS9053486
Manufacturer #: 650898A
This screw, also known as a shoulder bolt, is a genuine OEM replacement part for your lawn mower. This metal screw holds the starter grille in place against the rewing starter on your lawn mower. It r...
$5.15
In Stock
Lawn Mower Shoulder Bolt
PartSelect #: PS9046634
Manufacturer #: 614650
The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket...
$4.99
In Stock
Bowl Gasket Tecumseh
PartSelect #: PS9958948
Manufacturer #: 49-841
This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated...
No Longer Available
Snow Blower Nylon Insert Lock Nut
PartSelect #: PS9276436
Manufacturer #: 3296-29
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is use...
$5.95
In Stock
Lawn Mower Washer
PartSelect #: PS8963619
Manufacturer #: 40-1940
This OEM-sourced washer in your walk-behind lawnmower provides space and protects the rear wheel from rubbing against the pivot arm assembly, ensuring smooth wheel rotation. A damaged washer may appea...
$3.99
In Stock
Exact Part matches for your search term
[Viewing 2 of 2]
Hex Bolt, 1/4-20 X 2-inch
This part number matches the current model number 20009
PartSelect #: PS16737453
Manufacturer #: 20009
No Longer Available
Spring
This part number matches the current model number 20009
PartSelect #: PS18275061
Manufacturer #: 20009
No Longer Available
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The hub that the mower blade mounts to was broken
The hub that the mower blade mounts to was brokenPut the new Harbonne played and played securing flange bolted it up
Parts Used:
-
randy from HIGHLAND, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
8 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost PartSelect Number PS9053486; Tecumseh 650898A screw
I lost two of the screws that hold the plastic Lawn Boy cowling to the Tecumseh lv195ea engine. I just replaced the lost screws with the newly ordered screws.
Parts Used:
-
Steven from FAIRVIEW, TN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
3 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height ... Read more assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Read less
Parts Used:
-
Ray from YARDLEY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
3 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!