13AT61RH544 Toro - Overview
Models starting with 13AT61RH544
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Aluminum Push Rod
PartSelect #: PS9073139
Manufacturer #: 690982
This is a replacement push rod for your lawn tractor engine. It is made of aluminum and is the push rod used for the exhaust valve. Occasionally, the push rod in your engine can become damaged, and wi...
No Longer Available
Steel Push Rod
PartSelect #: PS9062983
Manufacturer #: 690981
This is a replacement steel push rod for your lawn tractor engine. The engine will have two push rods; one made of steel, and one made of aluminum. This part is made of steel and is approximately 6 in...
$8.91
Special Order
Engine Oil Seal
PartSelect #: PS9151828
Manufacturer #: 795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty...
$7.88
In Stock
Engine Cylinder Head Gasket
PartSelect #: PS9067184
Manufacturer #: 693997
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and ...
$26.91
In Stock
Engine Oil Seal
PartSelect #: PS9277860
Manufacturer #: 391086S
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "M...
$6.59
In Stock
Engine Governor Gear
PartSelect #: PS9151758
Manufacturer #: 793338
Ensure smooth and balanced operation of your Briggs and Stratton engine with this exceptional Gear Governor. It's intricately designed to maintain control over the speed of the engine, contributing to...
$30.58
Special Order
Common Symptoms of models starting with 13AT61RH544
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lost my main jets while cleaning old gas from carb.
I removed the fan shroud, the carb/manifold as an assembly,turned the carb upside down and removed the fuel bowl. I replaced only one jet. Not until this moment did I discover their were two jets in this nikki carb. I now have a second jet ordered and will install it Friday,hopefully. These jets are two different part numbers as one is a
... Read more
left jet and the other is a right one. Be careful when opening the fuel bowl as these jets are held in their bores by small O-rings, and nothing else. The brigg's and Stratton part numbers are 791501 for the left jet and 791502 for the right.
Read less
Parts Used:
-
dan from EASTPORT, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
11 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad governor
Look on YouTube for video's on how to replace a Briggs governor. There are several there. My favorite, with best explanation, is, "Easily Replace Briggs Governor Gear (V-Twin Intek Engine) with Taryl". https://www.youtube.com/watch?v=wn3eanGxSEA&t=152s.
Taryl (probably not his real name) does a very good job of showing step-by- ... Read more step the whole procedure, along with some additional hints/tricks/techniques of value.
Not including oil and filter, I spent less than $50 for a new governor, gasket, and drive shaft seal. That's all that is really necessary to replace is those three parts. That is, unless pieces of the old governor tore up a gear, valve, or something else. Inspect everything! {I was lucky and only the governor was destroyed}
One word of note. Be sure to clean out all of the debris from the blown governor. Be sure to remove the spark plugs and carefully rotate the drive shaft while looking for nooks-and-crannies where debris can hide. I tried to use a magnet to help, but it didn't help much, even though the block is aluminum.
Good luck.
Taryl (probably not his real name) does a very good job of showing step-by- ... Read more step the whole procedure, along with some additional hints/tricks/techniques of value.
Not including oil and filter, I spent less than $50 for a new governor, gasket, and drive shaft seal. That's all that is really necessary to replace is those three parts. That is, unless pieces of the old governor tore up a gear, valve, or something else. Inspect everything! {I was lucky and only the governor was destroyed}
One word of note. Be sure to clean out all of the debris from the blown governor. Be sure to remove the spark plugs and carefully rotate the drive shaft while looking for nooks-and-crannies where debris can hide. I tried to use a magnet to help, but it didn't help much, even though the block is aluminum.
Good luck.
Read less
Parts Used:
-
John from BROOKVILLE, IN
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Socket set, Wrench set
8 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rod broke ruining the case and camshaft
dissembled ordered repair parts, piston ,upper case, rod, camshaft, seal kit, and motor maintenance CD
The camshaft first provided did not have the compression release device on it and the cam lobe position was all wrong for the model engine I had. .
Parts Select provided me with the proper cam Shaft. Removed engine from mowe ... Read more r (Scag Freedom Z) 15 minutes, drained oil, flipped upside down removed bottom case, removed wrong cam shaft, reinstall new valve lifters, camshaft with decompression release on it matching dots on crankshaft. Used paint brush to coat all parts heavily with motor oil.
Do not put sealant on case gasket,(it might change crankshaft end play), retorqued bolt in alternating pattern, placed nylon pipe tape on drain plug threads, and reinstalled engine on mower. It started instantly and ran extremely smooth with no oil burn or vibration.
I am very happy with the support and quick mshipping Parts Select provided..
The camshaft first provided did not have the compression release device on it and the cam lobe position was all wrong for the model engine I had. .
Parts Select provided me with the proper cam Shaft. Removed engine from mowe ... Read more r (Scag Freedom Z) 15 minutes, drained oil, flipped upside down removed bottom case, removed wrong cam shaft, reinstall new valve lifters, camshaft with decompression release on it matching dots on crankshaft. Used paint brush to coat all parts heavily with motor oil.
Do not put sealant on case gasket,(it might change crankshaft end play), retorqued bolt in alternating pattern, placed nylon pipe tape on drain plug threads, and reinstalled engine on mower. It started instantly and ran extremely smooth with no oil burn or vibration.
I am very happy with the support and quick mshipping Parts Select provided..
Read less
Parts Used:
-
Arthur from SAINT JO, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!