13A2683G790 MTD - Overview
Models starting with 13A2683G790
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Lawn Mower Plastic Bushing
PartSelect #: PS9167515
Manufacturer #: 941-0475
This is an authentic OEM part for Craftsman lawn and garden equipment. This bushing has an internal diameter of 0.380", is made of durable black plastic, is not part of an assembly or kit, and is sold...
$5.95
In Stock
Joint
PartSelect #: PS9171232
Manufacturer #: 923-0448A
The Lock Ball Joint Assembly is part of the steering mechanism, and the machine will not be able to steer without it. This part attaches to the steering block and drag link. Installation is rated as "...
$25.97
On Order
Lawn Mower Mulching Blade
PartSelect #: PS9167946
Manufacturer #: 942-0616A
Dimension: 21.23-Inch
This is a Genuine Manufacturer Approved Blade used on Riding Mower/Lawn Tractor. This Blade is sold Individually. It is a 3-in-1 blade for mulch, bag and side discharge purpos...
$33.58
In Stock
Lawn Mower Plastic Flange Bearing
PartSelect #: PS9302372
Manufacturer #: 741-0487C
Made of durable silver plastic, this Flange Bearing is an authentic manufacturer-source replacement part for hundreds of models of lawn and garden equipment. It is used to allow a shaft to connect whi...
$7.91
In Stock
Snow Blower Washer
PartSelect #: PS10006541
Manufacturer #: 736-0242
Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between variou...
$5.17
Special Order
Engine Fuel Line Clamp
PartSelect #: PS8938782
Manufacturer #: 26460
The Fuel Line Clamp is a metal, individually sold part which clamps onto the fuel line, securing it to a port and preventing leaks. Installation is rated as "Easy" by customers and will require pliers...
$5.95
In Stock
Lawn Mower Brake Puck
PartSelect #: PS9165951
Manufacturer #: 917-0678
When the brakes are applied, this brake puck presses against the brake disc in your lawn equipment to help slow down or stop it. The brake puck is in the brake assembly, which might be located near th...
$7.91
In Stock
Lawn Mower Washer
PartSelect #: PS9311087
Manufacturer #: 936-0119
This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent ...
$4.95
In Stock
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Yardman / MTD wouldn't steer left, makes a popping and grinding noise when turning.
To disconnect the steering shaft to replace the bearing, there is a #3 Philips head screw on the underside of the deck which needs to be taken out. Chances are it hasn't been replaced before, so it is likely very tight. I ended up dropping the deck to allow for more room but it could probably be done with the deck in place the way I had t
... Read more
o do it. I had someone hold the steering wheel up top (not undoing the 13mm bolt holding the steering wheel in) and tried to unscrew the Philips, even after heating it with a torch still stripped out. The only way I could get the screw out was to take a pair of Vice Grips adjusted extremely tight to the outside of the screw and put the torch on it to heat it again. Then, turn the steering wheel to the left and when the Vice Grips get caught on the bottom of the mower, it will unthread the steering wheel from the screw. After the screw and washer are out *TAKE NOTE OF THE ORIENTATION OF THE WASHER*, I went to the hardware store and replaced the screw with a bolt that was 5/16 - 18 x .750 which was the closest length they had, took out the worn out bearing, popped in the new one, reinstalled the washer and bolt, then the deck. Even if you get the philips screw out without using Vice Grips, I would still recommend replacing it with a bolt.
Read less
Parts Used:
-
Patrick from Northville, NY
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
7 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Battery tray rusted out
Removed battery then replaced tray it sets in then, then reinstalled the battery
Parts Used:
-
Brian from LAGRANGE, KY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench (Adjustable)
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!