1284 Briggs and Stratton Engine - Overview
Models starting with 1284
Click on the best match to narrow your results.
- 128432-0035-E1 Briggs and Stratton Engine (Engine)
- 128432-0036-E1 Briggs and Stratton Engine (Engine)
- 128432-0116-E1 Briggs and Stratton Engine (Engine)
- 128432-0132-E1 Briggs and Stratton Engine (Engine)
- 128437-0050-E1 Briggs and Stratton Engine (Engine)
- 128452-0049-E1 Briggs and Stratton Engine (Engine)
Keep searches simple, eg. "belt" or "pump".
Engine Ratchet Pawl
PartSelect #: PS8942598
Manufacturer #: 281505S
The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will...
$3.99
In Stock
Engine Float Valve Kit
PartSelect #: PS8963322
Manufacturer #: 398188
This needle and seat kit, also known as a float valve, is found in many types of liquid-fueled lawn equipment, such as carburetors. The valve regulates the flow of fuel into the float bowl. The needle...
$6.97
In Stock
Engine Pulley Spring Assembly
PartSelect #: PS8988822
Manufacturer #: 498144
Upgrade your equipment with this reliable Pulley/Spring Assembly from Briggs and Stratton. Known for their superior quality, Briggs and Stratton parts are designed to help prolong the life of your mac...
$20.78
In Stock
Engine Fuel Tank
PartSelect #: PS9141053
Manufacturer #: 799863
This genuine fuel tank assembly is sourced directly from the original equipment manufacturer and is specifically designed for use with Briggs & Stratton engines on lawn and garden equipment. It serves...
$98.07
In Stock
Engine Oil Seal
PartSelect #: PS8948679
Manufacturer #: 299819S
This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should ...
$5.99
In Stock
Exact Part matches for your search term
[Viewing 1 of 1]
Spindle
This part number matches the current model number 1284
PartSelect #: PS10335459
Manufacturer #: 1284
$224.50
Special Order
Common Symptoms of models starting with 1284
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Cannot pull starter cord out or engine will not turn over
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mistreated Briggs & Stratton 206 CC Engine on MTD Chipper
Removed tank and drained old gas.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Removed and disassembled carb. Needed new gaskets and seals, and had to clean corn syrup glaze (separated ethanol) from bowl and everywhere else with carb cleaner.
Throttle linkage was de-plating/rusty. Steel wool and WD40 got it moving again.
Cleaned spark plug electrode.
Reassemble ... Read more d, poured Sea Foam in the bottom of the tank and gave it a few pulls.
Let Sea Foam sit for a while, then filled the tank with Premium.
Blew white smoke for a minute then ran like new. Shredded for a while, then changed the oil.
Read less
Parts Used:
-
Dana from HAMMOND, IN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
7 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Parts fit like a glove
Removed pull start assembly down to the crank. Installed motor housing, motor fan & rewind assembly. All went real good.
Parts Used:
-
Wayne from OOLTEWAH, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Starter Rewind broke internally-rope did not work
Removed old broken rewind starter (4 bolts); found the Model and Serial numbers; found Parts Direct and ordered new assembly; upon delivery, reinstalled with new Starter and hardware.
Parts Used:
-
Mark from N FRANKLIN, CT
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!