Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$10.95
In Stock
Order within the next 0 mins and your part ships today!
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollabl...
$10.45
In Stock
Order within the next 0 mins and your part ships today!
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appli...
$24.95
In Stock
Order within the next 0 mins and your part ships today!
This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint c...
$10.45
In Stock
Order within the next 0 mins and your part ships today!
This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edge, black in color, a...
$7.95
In Stock
Order within the next 0 mins and your part ships today!
Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature within the dryer. This particular cycling thermostat can be adjusted between 135 and 155 de...
$45.95
In Stock
Order within the next 0 mins and your part ships today!
Questions And Answers for 11081422510
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Matthew
February 4, 2024
The washer operates normally, however, the dryer doesn't start. The door switch is functioning normally. What would be the next part to check?
For model number 11081422510
Hello Matthew, thank you for getting in touch. Based on our understanding of the issue, we would suggest checking the timer, part number PS11741711, to solve the problem. We hope that helps!
The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was included on both sides so i did not need to repair the catch. I still have the part so when it breaks again, I can just pop it in.
First I removed the fabric softener container and set it aside. Below that, there is a plastic cover with a rubber gasket that distributes the fabric softener. I also just pulled that out and set it aside. Below that was an 11mm bolt that attached the upper and lower agitator to the drive mechanisim. The lower agitator is attached dir
... Read moreectly to the shaft and that was working properly so I knew it was't a motor or drive issue. Until it broke, the top half of the agitator sat still for a second, then it turned clockwise with the lower agitator. This helped push the clothes down to the lower part to be circulated throughout the wash cycle. Well, now the upper agitator just sat there, like it wasn't attached to anything at all. Below the aforementioned plastic cover with the rubber gasket, I found a part that had 4 plastic "teeth" that moved in and out, releasing and grabbing the inside of the upper agitator, respectively. Over time, these teeth wore down and stopped "grabbing" the ridges on the inner part of the upper agitator, causing it to stop turning with the lower agitator. I removed the 11mm bolt and tried to seperate the upper agitator from the lower agitator to replace the teeth. This part was kind of tough to get out because the plastic clips that held it in were deformed. I just had to pull hard and eventually it came apart. In the process, I broke two of the clips. I wasn't really concerned because the 11mm bolt holds everything in place anyway. After that I just swapped out the worn teeth with the new ones. I put it back together in the opposide order I took it apart and viola....good as new. And it only cost me $15 bucks.
