Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a manufacturer-approved replacement drain pump for your washing machine. To complete this repair you will need a 1/4 inch nut driver, 5/16ths nut driver, a flat blade screwdriver, and a pair o...
$108.95
In Stock
Order within the next 41 mins and your part ships today!
Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$7.95
In Stock
Order within the next 41 mins and your part ships today!
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is imp...
$6.95
In Stock
Order within the next 41 mins and your part ships today!
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$12.58
In Stock
Order within the next 41 mins and your part ships today!
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
$30.41
In Stock
Order within the next 41 mins and your part ships today!
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature or amount of water needed.
$50.44
In Stock
Order within the next 41 mins and your part ships today!
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is...
$40.90
In Stock
Order within the next 41 mins and your part ships today!
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place o...
$22.95
In Stock
Order within the next 41 mins and your part ships today!
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dave
February 2, 2023
Replaced pump but comes up with code F30 won’t let water in
For model number 11047532601
Hi Dave,
Thank you for your question. The F-30 error code indicates a dispenser system error. This can occur when the linkage between the dispenser motor and the dispenser has failed, if there is a loose wiring connection between the central control unit and the dispenser motor, or if the dispenser motor has failed. If the dispenser motor makes a clicking noise when it turns or if it turns continuously, then it has failed and will need to be replaced. If the dispenser motor is fine and everything else checks out, then you will need to replace the central control unit. If you have any questions, please let us know. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Michael
November 3, 2023
Start button when pushed will not start machine. Ran through the diagnostic test and all worked but the button works was working but very finicky until now won’t start the machine
For model number 11047532601
Hello Michael, thank you for contacting us. Based on our understanding of the issue, we would suggest checking the control board, part number PS11746714, to solve the problem. We hope this helps!
Washer will turn on with add garment light on and lock door but won't start a cycle. Won't unlock door even if stop button is pushed - - add garment light will flash. Error code F28 has come on. Washer is drained. Washed a bunch of towels and F22 light went on and drained tub. Then on next load washer stopped at 1 minute, wouldn't unlock, wouldn't turn off. Unplugged unit for 30 minutes, then plugged back in, then turned on: Washer will turn on with add garment light on and lock door but won't start a cycle. Won't unlock door even if stop button is pushed - - add garment light will flash. Won't turn off.
For model number 11047532601
Hello James, thank you for your question. The F28 error code indicates a communication error between the control boards. Check the connections. There are three screws on the rear of the top panel that secure the top on. Once removed, the top will slide back and come off to be set aside. In the right front corner near the front control panel is the main machine control. Remove each connector, one at a time, and replace into the control. This will rectify any connection issue if there is one. Once each connector has been reset into position, remove the back panel from the machine to access the motor control board. Do the same for each motor connector. Plug the machine back in and see if the code returns. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find
... Read moreanything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module.
