09085-4 Briggs and Stratton Generator - Overview
Sections of the 09085-4
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Lawn Mower Spark Plug
PartSelect #: PS9140427
Manufacturer #: 796112S
This part is the replacement spark plug for your engine. It measures approximately 2.5 inches by 1 inch. The spark plug creates the spark that ignites fuel in your engine during the combustion process...
$4.99
In Stock
Fuel Valve W/Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$19.38
In Stock
Engine Oil Seal
PartSelect #: PS9277860
Manufacturer #: 391086S
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "M...
$6.59
In Stock
Engine Starter Pulley
PartSelect #: PS8942071
Manufacturer #: 295871
Introducing the Briggs and Stratton Starter Pulley, a vital component for your appliance repair needs. Crafted with quality and precision, this pulley plays a significant role in your engine's start-u...
$15.80
In Stock
Engine Starter Clutch
PartSelect #: PS8968281
Manufacturer #: 399671
Discover the power of optimal engine performance with the Briggs and Stratton Starter Clutch. A vital piece of your garden equipment's engine, this starter clutch engages your machine's flywheel while...
$37.32
In Stock
Engine Carburetor Overhaul Kit
PartSelect #: PS8960042
Manufacturer #: 394693
Introducing the Carburetor Overhaul Kit from Briggs and Stratton! This high-quality product is designed to effectively overhaul and enhance the performance of your carburetor. Carefully constructed to...
$37.35
In Stock
Questions And Answers for 09085-4
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 09085-4
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
6 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
8 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!