03053 Briggs and Stratton - Overview
Models starting with 03053
Click on the best match to narrow your results.
- 030534-0 Briggs and Stratton Generator (Briggs & Stratton Generator Model 030534-0 (0305340, 030534 0) Parts)
- 030535-0 Briggs and Stratton Generator (Briggs & Stratton Generator Model 030535-0 (0305350, 030535 0) Parts)
- 030535-00 Briggs and Stratton Pressure Washer (Briggs & Stratton Pressure Washer Model 030535-00 (03053500, 030535 00) Parts)
- 030536-0 Briggs and Stratton Generator (Briggs & Stratton Generator Model 030536-0 (0305360, 030536 0) Parts)
Keep searches simple, eg. "belt" or "pump".
Fuel Valve W/Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$19.38
In Stock
Fuel Gauge Cap
PartSelect #: PS9314364
Manufacturer #: B4363GS
This OEM replacement fuel gauge cap is designed for use in generators. It comes in a cylindrical shape and has a built-in window to easily view the fuel levels without pulling out the entire cap. It i...
$45.46
Special Order
Fuel Line
PartSelect #: PS9140673
Manufacturer #: 791745
This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to tra...
$11.29
Special Order
Engine Starter Solenoid
PartSelect #: PS9064363
Manufacturer #: 691656
A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acti...
$35.02
Special Order
Voltage Regulator
PartSelect #: PS9270265
Manufacturer #: 205858GS
The OEM voltage regulator or voltage control is a part used to regulate the voltage so it can provide the right amount of power to electrical components. It attaches inside the alternator housing. The...
$120.00
In Stock
Air Compressor Key
PartSelect #: PS8928085
Manufacturer #: 23139GS
Designed for use in various models of pressure washers, air compressors, and generators, this Woodruff Key is used to hold a shaft with a mating part, such as a gear. It is 1 inch in length, made of m...
$4.99
In Stock
Garden Hose Filter
PartSelect #: PS9181874
Manufacturer #: B2384GS
This filter, also known as a water inlet screen, is designed for use with pressure washers and has a 1-inch diameter (including the surrounding rubber housing). The filter itself is made of mesh and i...
$4.99
In Stock
Hose
PartSelect #: PS11829845
Manufacturer #: 708962
This replacement hose is a genuine OEM sourced item that specially produced for use with Craftsman pressure washers. This 25 ft. high-pressure hose is made of durable rubber with metal fittings and it...
No Longer Available
Common Symptoms of models starting with 03053
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wouldn’t start.
I installed a new solenoid starter. Took me a total of 20 minutes. Started right up.
Parts Used:
-
Bruce from CARNATION, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
13 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
6 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!