020287-0 Troy-Bilt Pressure Washer - Overview
Sections of the 020287-0
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Chemical Injection Kit
PartSelect #: PS8911045
Manufacturer #: 192914GS
Used to connect the hose that supplies the chemical cleaning solution (soap), this OEM replacement Chemical Injection Kit consists of the brass fittings, a metal ball, a spring, and a rubber seal, and...
$27.40
In Stock
Thermal Relief Valve
PartSelect #: PS9270416
Manufacturer #: 208673GS
Sourced directly from the manufacturer, this part is used to open and release hot water if the water exceeds the maximum operating temperature. It has metal and plastic components, is not part of a ki...
$16.05
In Stock
Garden Hose Filter
PartSelect #: PS9181874
Manufacturer #: B2384GS
This filter, also known as a water inlet screen, is designed for use with pressure washers and has a 1-inch diameter (including the surrounding rubber housing). The filter itself is made of mesh and i...
$4.99
In Stock
Vibe Mount Kit
PartSelect #: PS8910434
Manufacturer #: 192310GS
Frequently referred to as a Vibration Kit, this Vibe Mount Kit includes two durable rubber mounts, two metal washers, two bolts, and two locknuts. This kit is sourced directly from the manufacturer fo...
$10.55
In Stock
Handle Fastening Kit
PartSelect #: PS9181264
Manufacturer #: B2203GS
This handle fastening kit includes two plastic thread wingnuts and two carriage bolts, which are essential for securely attaching the handle assembly to your pressure washer. The handle assembly is ty...
$5.74
In Stock
E-Ring
PartSelect #: PS10000220
Manufacturer #: 703977
The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.
$4.99
In Stock
Grommet
PartSelect #: PS8950513
Manufacturer #: 30809GS
This replacement part is used on the base of various models of pressure washers to reduce vibration from the pump. This Grommet has an O.D. of 1 inch, is not part of a kit or assembly, is sold individ...
$4.99
In Stock
Questions And Answers for 020287-0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The copper fitting on the chemical injection broke.
I order the part from this site and received it within a week. the only problem was that spring was missing out of the sealed bag. NO PROBLEM!!! I cut a ball point pen spring to fit and everything works just fine. You just have to remember to put the spring in first, then the ball bearing and then the rubber o-ring.If you put them in back
... Read more
wards you pressure will fed directly into your chemical container!!
Read less
Parts Used:
-
Carl from ARCADIA, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
11 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The foward motor mounts both failed allowing the entire engine and pump to swing back
I loosened the rear motor mounts which protrude through slots in the frame using a 15mm open end allowing the engine to be moved enough to pass the front mounts through both the frame and the engine mounting holes. The upper bolts on the front mounts don't have enough clearance for a socket or box end and the open end gets less than a qua
... Read more
rter turn at a time unless you remove the wheels. I just took my time and tightened the nuts being careful not to round the corners. The lower bolt/nuts present no problem.
Read less
Parts Used:
-
Edward from BANGOR, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!