01150-0 Briggs and Stratton Generator - Overview
Sections of the 01150-0
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve W/Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$19.38
In Stock
Engine Fuel Line Clamp
PartSelect #: PS8938782
Manufacturer #: 26460
The Fuel Line Clamp is a metal, individually sold part which clamps onto the fuel line, securing it to a port and preventing leaks. Installation is rated as "Easy" by customers and will require pliers...
$5.95
In Stock
Inlet Needle, Seat, And Clip Assembly
PartSelect #: PS9052162
Manufacturer #: 631021B
No Longer Available
Trimmer Breather Gasket
PartSelect #: PS8942323
Manufacturer #: 27896A
This OEM valve cover gasket, also known as the breather gasket, creates a seal between the breather body and cylinder block in your lawn equipment. Made of flexible plastic, it measures 2 inches by 4 ...
$5.15
In Stock
Trimmer Breather Element
PartSelect #: PS9274720
Manufacturer #: 28424
This breather element is also called an air filter cartridge, cleaner element, or engine filter. It prevents debris from reaching the carburetor of your lawn equipment while allowing clean air to ente...
$5.95
In Stock
Questions And Answers for 01150-0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 01150-0
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
6 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
8 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!