Kenmore Washer Dryer Combo Wire Plugs and Connectors

Videos!

Your Price

$18.95

Kenmore Washer Dryer Combo Washer Drive Block 2 5/16 High

★★★★★

2 Reviews

PartSelect Number PS11741977

Manufacturer Part Number WP389140

This part is for large capacity belt drive and direct drive appliances.

Fixes these symptoms

Leaking
Spins slowly
Will not agitate
See more...

Installation Instructions

Dexter from Milwaukie, OR

Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose

After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go. Read more...

Your Price

$18.95

Kenmore Washer Dryer Combo Dryer Terminal Block

★★★★★

1 Review

PartSelect Number PS11741489

Manufacturer Part Number WP3397659

This part is an electrical connector where you can attach wires. This part does NOT included the wires, screws, and nuts. Must be order separately

Installation Instructions

DAVID from LEESBURG, FL

One of the power cord connections on the terminal block was loose. Screw on terminal block was cross threaded when installed. Took six years to smoke the wire.

Removed and replaced terminal block, power cord and black wire to timer. Read more...

Your Price

$52.45

Kenmore Washer Dryer Combo Terminal And Wire Kit

PartSelect Number PS334181

Manufacturer Part Number 279318

Your Price

$18.95

Kenmore Washer Dryer Combo 3-circuit T.p.a. Connector Plug

★★★★★

2 Reviews

PartSelect Number PS11741226

Manufacturer Part Number WP3360056

Fixes these symptoms

Burning smell
Will Not Start
See more...

Your Price

$47.95

Kenmore Washer Dryer Combo Terminal Block

PartSelect Number PS724728

Manufacturer Part Number 134037400

Installation Instructions

Emily from Raleigh, NC

Dryer wouldnt turn on

I thought the problem was electrical so I inspected the power cord and noticed a burn on the ground connection. I disconnected the wires and inside the block was melted so I replaced it making sure the connection was tight between the power cord and block. It runs no problem. I think the dryer shorted because of a loose connection. Read more...

Your Price

$53.95

Kenmore Washer Dryer Combo Terminal Block

PartSelect Number PS445924

Manufacturer Part Number 3202786

Your Price

$54.95

Kenmore Washer Dryer Combo Dryer Terminal Block Kit

★★★★★

2 Reviews

PartSelect Number PS419369

Manufacturer Part Number 134101400

This kit includes 3 screws and 3 terminals.

Installation Instructions

Arthur from Grand Prairie, TX

Terminal Block Melts when power cord connector is left loose by install crew.

1) Removed Top Dryer Cover (pushed 2 compression clips on front side 1" from top and 2" in from each side) to gain access to terminal block in rear.
2) Removed 2 screws over terminal block cover and 2 screws holding bad terminal block in place. Removed 3 screws holding bad power cord,
3) Removed good terminal connectors from bad terminal block and reinstalled them in the new terminal block.
4) Cut dryer wire from bad terminal block connector and soldered (optional) them to the new terminal block connector. Installed this connector into the new terminal block.
5) Installed new terminal block in dryer with 2 screws.
6) Installed new power cord on new terminal block ensuring contacts were tight and cord had pull guard properly installed. Reinstalled terminal block cover with 2 screws.
7) Reinstalled Dryer Top Cover. Read more...