Kenmore Wall Oven Seals and Gaskets

Your Price

$11.13

Kenmore Wall Oven Light Gasket

★★★★★

5 Reviews

PartSelect Number PS11740863

Manufacturer Part Number WP3184533

This part creates a seal around the light lens and bulb.

Installation Instructions

David from Westminster, CO

Fiber Gasket around Pyrex Light Lens was mis-shaped

All I had to do was unscrew the pyrex lens over the oven light and then remove the old gasket and replace it with the new one. Worked like a champ! Read more...

Your Price

$110.59

Kenmore Wall Oven GASKET

★★★★★

3 Reviews

PartSelect Number PS442156

Manufacturer Part Number 318053103

This oven door gasket prevents heat from escaping the oven cavity when in use. It contains all of the attaching clips needed for installation.

Installation Instructions

Vicki from Warrenton, MO

the gasket around the oven door was severly scorced and hard. Would no longer seal door.

Easier than painting my toenails!! The gasket came out easily just by pulling with my hands. Replacing it with the new one was even simpler. The clips are already attached to the gasket and easily slip into the holes on the door. I used the end of a tupperware orange peeler to push the unfinished ends of the gasket into a slot at the bottom and that was it! A new, perfect seal and it looks and works great! Read more...

Videos!

Your Price

$143.25

Kenmore Wall Oven Door Seal

PartSelect Number PS977704

Manufacturer Part Number 316405000

Installation Instructions

Frank from PALM COAST, FL

My oven door seal was worn and did not seat properly. It leaked heat.The infinite burner was not warming in the low heat positions

I followed two very good videos on how to do the repairs. It took longer to clean all the disassembled parts and the glass than it did to actually do the repair.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to lock them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well. Read more...

Your Price

$126.95

Kenmore Wall Oven Oven Door Seal

★★★★★

5 Reviews

PartSelect Number PS11757564

Manufacturer Part Number WPY702338

This oven door seal prevents heat from escaping the oven cavity when in use.

Fixes these symptoms

Little to no heat when baking
Oven not heating evenly
See more...

Installation Instructions

Paul from Mickleton, NJ

The oven door seal was ripped and was leaking.

The oven seal replacement was very straight forward. Two screws held the door to the arms coming from the oven. I slid the door up off the arm and moved it to a workbench. This whole process should take about 15 minutes, a little longer if your unit is older and you want to clean as you go. Mine was fairly dirty and I gave it a cleaning as I removed parts. Unscrew all screws on the outer frame of the door, including two small ones on the side. Remove the outer frame and then the glass front and set them aside. A few more screws to remove the glass from the inner door, and even more on the remaining part of the door. You should also remove the screws holding the tiny brackets as well to release the portion that holds the oven seal in place. This is very straightforward, just keep pulling screws out until you can remove the old seal.

Once the old seal is out, insert the new one using the wire embedded in the seal as your guide...the gap in the seal goes to the bottom. Put everything back together and re-install the door. My door hinges were spring loaded and took a little effort to move them down so the door can be slipped on. This is a two person job since the hinges do not lock in place, they spring right back up flush with the oven and you cannot install the door. Re-install the two set screws holding the door to the hinges and you are done!

With the new seal in place, it felt a little puffy and the door did not seem to close as flush as it used to. This makes sense since the seal is new. I kept the door locked (like you would to use the oven cleaning cycle). I even kept it partially locked during cooking.

Frankly, the hardest part was the cleanup of nasty grease and dirt that built up over the past decade or so.

Best of luck! Read more...

Your Price

$126.71

Kenmore Wall Oven Oven Door Seal

★★★★★

1 Review

PartSelect Number PS11743839

Manufacturer Part Number WP701650

This oven door seal is twenty-one inches wide. This woven style door gasket is gray in color.

Installation Instructions

Rosemary from Pawleys Island, SC

seal was black and stiff from burned in spilled grease and sauce

Unscrewed and pulled the door off and then took the three layers of the door apart in order to clean off the burned-on goop and remove the old and insert the new seal. The last screw was rusted in and the drill stripped it so that it was impossible to remove. I levered the remaining two layers apart, holding them open with screw drivers, and inserted the new seal. Had to be careful with the shaping of the metal core of the seal and the distribution of the sealing fabric. Phew! I saved the screws from each layer separately by taping them to the counter in the order of removal. This made reassembly easier. Getting the door back on was a bit difficult and I needed another pair of hands to help me. Read more...

Your Price

$123.06

Kenmore Wall Oven Lower Oven Door Gasket

★★★★★

1 Review

PartSelect Number PS754417

Manufacturer Part Number WB41T10003

Installation Instructions

William from Lantana, TX

Seal worn on corner allowing heat to escape, sensor not reading the correct temperature

Spring clips installed on seal just pull off door. New clips get inserted in mounting holes and are pushed in to seat in door. Seal ends slide into door holes.

Replaced old sensor with new one by removing nut screw and carefully pulling sensor cable out of oven back until plastic terminal connection is exposed. Sensor connection has a locking tab that must be pushed in to release sensor connector. Do not allow oven wire to pull back into back of oven until new sensor is connected. Reinstall nut screw and tight to hold new sensor in place. Verify proper oven operation. Read more...