Crosley Washer Dryer Combo Hardware

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Crosley Appliance Parts
Shop By Part Type

Popular Crosley Washer Dryer Combo Hardware

Videos!
Your Price
$13.41
  In Stock
Crosley Washer Dryer Combo Roller Support Tri-Ring
★★★★★
★★★★★
5 Reviews
PartSelect Number PS11755850
Manufacturer Part Number WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Fixes these symptoms
Installation Instructions
John from Tucson, AZ
worn out part
The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair. Read more...
Videos!
Your Price
$7.03
  In Stock
Crosley Washer Dryer Combo Agitator Bolt
★★★★★
★★★★★
10 Reviews
PartSelect Number PS11741866
Manufacturer Part Number WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
Fixes these symptoms
  • Leaking
  • Marks left on clothes
  • Spinning Issues
  • See more...
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go. Read more...
Videos!
Your Price
$7.95
  In Stock
Crosley Washer Dryer Combo Thrust Washer
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11740482
Manufacturer Part Number WP233520
This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found on dryers around the drum support rollers and idler pulleys, and helps prevent the rollers and pulleys from bumping up against the brackets they are installed on. Your thrust washer could be defective if you notice your dryer wont tumble, rotate, or turn; or there is a load squealing or whining noise when the dryer tumbles. The repair is a relatively easy job. You will require a putty knife, 5/16 inch nut driver, and E-Ring pliers. Remember to disconnect the power to your dryer before you begin the repair.
Fixes these symptoms
Installation Instructions
Chris from Hopedale, MA
Drum not centered , clothes getting stuck in dryer
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it. Read more...
Your Price
$5.41
  In Stock
Crosley Washer Dryer Combo Screw, 8/18 x 3/8
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...
Your Price
$16.44
  In Stock
Crosley Washer Dryer Combo Single Front Panel Cip
★★★★★
★★★★★
3 Reviews
PartSelect Number PS11731288
Manufacturer Part Number W10854425
This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.
Fixes these symptoms
Installation Instructions
Sean from BAR NUNN, WY
Belt was slipping, and having a hard time spinning the drum
First off, start by turning of the breaker to the dryer and confirming the power has been turned off. Next, remove the lint screen and two screws holding the lint screen housing to the lid. Remove the two side moldings on the control panel and the two screws holding doun the enclosure. Slide the control enclosure forward and lift up . Take a picture of the wiring for later reference and carefully unplug the wires and set the enclosure aside. Next, remove the two screws holding the rear lid retaining clips. Gently pry up on the front of the lid to realese hold doun clips, swing the lid up and remove it from the rear clips, set the lid aside. Remove the two screws on corners of front cover located near the top, unplug the door switch. Remove the front cover by lifting straight up, set aside. Now remove the belt from the motor by realeasing the tensioner and remove it from the drum. You can now remove the drum through the front. Now is a good time to check the condition of your drum rollers, clean them as needed or replace them. Clean the roller shafts and apply a quality grease. "Clean the roller groove on the drum" this is what makes the drum sound bumpy! Remove the rear seal and replace it as per the instructions that come with the seal. The glue dries quickly, so have the seal fully in place and apply glue to small areas replacing the seal fully before moving on. You can now reinstall the drum being careful not to damage the seal. Place the drum on the rollers, reach inside and work the seal into place. You can now replace the belt and work in reverse with the casings! It took me longer to type these instructions than it did to make this repair! Enjoy your like new machine! Read more...
Your Price
$8.00
  In Stock
Crosley Washer Dryer Combo Knob Spring-Clip
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11743754
Manufacturer Part Number WP688805
Also known as the inside sleeve for the knob to be able to properly fit over the shaft of the switch. Sold individually.
Installation Instructions
Susan from UNIVERSITY PL, WA
Timer knob was cracked, missing spring clip and wouldn't set accurate drying time
I ordered the timer knob and read that I also needed the knob spring clip (this part is non-returnable), so I ordered both. Upon arrival I found that the knob spring clip already comes installed inside the shaft of the timer knob. So you don't need to order both. It was the easiest repair I've ever done. Just position timer knob on D-shaped shaft of dryer timer and push until knob clicks into place. Read more...
Your Price
$7.95
  In Stock
Crosley Washer Dryer Combo Screw - 10-16 x 1
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11741409
Manufacturer Part Number WP3387230
This screw is sold individually.
Installation Instructions
Wendy from BRAINTREE, MA
Freezer handle came loose on one side
Discovered that the seating in the handle was stripped on one side so removed the old handle (toughest part of the repair). Based on a previously asked/answered question, the PartSelect website provided an accurate list of the required parts (and corresponding part numbers) so I had everything I needed. Installing the new handle was very straightforward and quick. Read more...
Videos!
Your Price
$13.30
  In Stock
Crosley Washer Dryer Combo Drive Belt - 6 ribs
★★★★★
★★★★★
2 Reviews
PartSelect Number PS419285
Manufacturer Part Number 134051000
This is a drive belt for your washing machine. This part spins the basket in your appliance by connecting the drive motor to the drive system. You will need to replace the drive belt if your pumps are not spinning, your washer is not agitating, or you are noticing excess noise and/or a burning smell. This belt is black with six ribbings. To replace this part, you will need a Phillips screwdriver.
Fixes these symptoms
  • Burning smell
  • Spins slowly
  • Will not agitate
  • See more...
Installation Instructions
Carmen from Foreston, MN
motor burned out, tub quit going around
First I turned off the water and disconnected the hoses. I took off the back panel and unscrewed the 4 bolts holding the motor in place. The grounding screw was impossible to remove, so I had to cut the wire off. Took out motor and disconnected the electrical connector. Put new motor in (ordered new belt, figuring it would need replacing - was still in excellent shape, but replaced it anyway), bolted in the motor (socket set works best on further away bolts, screwdriver for closer ones). Put the belt on the motor first and then pulled it up over the side of the tub and turned the tub to get it around the whole tub - took alittle bit of turning to get it on. Plugged in electrical connector and screwed grounding wire into hole. Replaced back panel and water hoses. Got a bit dirty and sweaty but not too hard to do it yourself, as I am a 48 yr woman and don't usually do this kind of thing. Read more...
Videos!
Your Price
$47.65
  In Stock
Crosley Washer Dryer Combo Single Spring with Insulators
★★★★★
★★★★★
4 Reviews
PartSelect Number PS735645
Manufacturer Part Number 134144700
This is a single spring with insulator, but you may also know it as a suspension spring. It is a part for your washing machine. If your tub is no longer stable, which would cause shaking, moving, and excess noise, you may need to replace this part. The tools you will need in order to make this repair include a Phillips screwdriver and a pair of locking pliers. You will find the insulator on each end of this piece. We recommend replacing both springs in your appliance at the same time to ensure even wear.
Fixes these symptoms
Installation Instructions
Eric from Hillsboro, OR
Inner support spring and vibration shock both broke - tub dropped down within the washer
Remove power
Remove water connections
Pull out washer to have sufficient room to access the back and the top.
Removed the top panel (4 screws at top- back)
Removed the back panel (a lot of screws)
Removed small metal retainer strip on top edge over broken spring
Removed broken spring, hung top of new one.
Pulled up tub to as I stretched out the spring to mount spring to tub
From the back, unplug and remove 2 crews holding the electronic motor control unit from lower left

For both shocks:
This was the most "difficult" part - locate the 2 plastic retainer pins holding the shock, locate the tooth (or tab) holding the pin in place and push the tab in (I had to use some leverage - its stiff plastic covered in grease - a spare screwdriver handle helps to push the tab down).

After pins are removed, shock just pulls out (weight of the tub handled by the suspension springs).

Replace with new shocks (1 pack has a pair), replace pins.

Reinstall motor control unit.

Reassemble frame. reattach water supply lines.

I had to plug in the washer, activate a cycle, then unplug/plug in the washer again.

It helps to have a screwdriver attachment for a variable speed drill to handle all of the screws.

All told - about 45 minutes, most of this spent on removing the pins. Read more...
Your Price
$11.76
  In Stock
Crosley Washer Dryer Combo SCREW
PartSelect Number PS417085
Manufacturer Part Number 131168200
Sold individually.
Installation Instructions
Glenn from Fort Worth, TX
Dryer squealed loudly
First, I removed the top panel which is held on at the front by pressure clips. Second, I removed the entire front panel which entailed removing 2 screws and 2 wire couplings. Third, I removed the 3 screws on the inside center of the drum which turned out to be unnecessary. Fourth, I slid the drum forward in order to access the rear bearing. Lastly, I replaced the entire bearing assembly including the shaft, bracket, bearing, grounding ball and clip. Again, probably not needed but I had ordered the parts in advance in preparation for the worst. Read more...

Related Crosley Washer Dryer Combo Parts

Back to Top