Washer Dryer Combo Hoses and Tubes
Popular Washer Dryer Combo Hoses and Tubes
Washer Dryer Combo FILL HOSE
PartSelect Number PS16745853
Manufacturer Part Number 5304533220
Washer Fill Hose
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
keith from ROBERTSDALE, AL
fill hose got a hole in it
had to remove cover plate from under dryer and remove the top of washer to access the fill tube. horn part of fill tube is held in with one screw and plastic pin, the end with clamp that fits on the fill valve is very difficult to reach. could only get a grip on the clamp with 90 degree needle nose pliers. NOTE: washer cabinet has very sharp edges and cut my arm in several places trying to reach clamp. suggest wear long sleeve shirt.
Read more...
Your Price
$21.89
In Stock
Washer Dryer Combo Washer Drain Hose
PartSelect Number PS12578897
Manufacturer Part Number W11244231
The drain hose carries used water from the washer to your house drain.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Delmar from EAST TROY, WI
replaced drain hose that was missing
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Read more...
Washer Dryer Combo Washer Hose with Bellows
PartSelect Number PS3523347
Manufacturer Part Number 4738ER1004B
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillips head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
mark from AUBURN, CA
LG washing machine flooded the Landry room.
Wife called me and said the washing machine just flooded the Landry room. I looked at it and didn't see anything wrong. Took the top off and the back off and started looking for a leak, did not see anything. Took the front part of the washer apart thinking the drain hole was plugged up where the rubber boot is. It was ok after taking the big rubber boot off or whatever that is called i was not getting anywhere. I put it back together left the top and the back off. I turned the water on and started the washer on a quick cycle looking for a leak. I found the bellows at the inlet had a small leak fixed that and started the washer again. So what i found out was the clean out drain plug was not in tight letting water out as it was washing after i tightened it all was ok. So i did find a leak that was small that we never saw. The hardest part was putting that wire clamp on the rubber boot it took two people to do that.
Read more...
Your Price
$21.30
In Stock
Washer Dryer Combo Rubber Injector Valve
PartSelect Number PS11738945
Manufacturer Part Number WP216201
This part is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle. It is black in color and measures approximately 2 inches in length. To access this part, you will need to remove the front panel of your washer. There will be 2 screws holding it in place. Once these have been removed, the top will pivot to open, which will give you access to the injector assembly. This is an OEM part that comes right from the manufacturer and is sold individually.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Catherine from Wyandotte, MI
Front load washing machine leaking on floor while in fill mode.
Removed two screws at bottom of front panel and then removed front panel. Then removed two self-tapping bolts (one on each side) holding top panel in place and swung the panel up, out of the way, to expose top of tub and water injection components. Cut off one pinch clamp and loosened screw clamp holding two injector hoses to the injector sleeve. Removed these water injector hoses from injector sleeve assembly which is mounted on top of left side panel upper flange. Replaced deteriorated rubber injector valve, nozzle and the sleeve for the injector (plastic housing containing the injector valve and nozzle). Also replaced deteriorated injector tube seal where injector tube elbow mounts to top of tub assembly. Reinstalled injector hoses with a replacement screw clamp to replace the one cut off. tightened the new clamp and the other, original, screw clamp and checked for leaks. This solved the leakage problem. Secured top panel and re-installed front panel. Hardest part of the task was determining where the leak emanated from but once found and parts ordered, it was a relative snap to fix.
Read more...
Your Price
$41.76
In Stock
Washer Dryer Combo Tub-to-Pump Drain Hose
PartSelect Number PS3523345
Manufacturer Part Number 4738ER1002A
This is a tub-to-pump drain hose for a front load washer. The hose features flexible bellows which allow it to expand and contract when necessary. It carries the water from the tub of the washer to the drain pump so the used water can properly empty from the tub. This part is made of rubber, is black in color and measures 13 inches long. Be sure to drain the excess water from the washer before completing this repair. This is an authentic OEM part that is sourced directly from the manufacturer.
Fixes these symptoms
- Leaking
- Will not drain
- See more...
Installation Instructions
Leslie from STOWE, VT
leaking tub-to-pump drain hose
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
Read more...
Washer Dryer Combo HOSE ASSEMBLY,DRAIN
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor). Read more...
PartSelect Number PS8749199
Manufacturer Part Number AEM73732901
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pump, and it is responsible for transporting water out of the washing machine after a cycle. If the drain hose is kinked, damaged, or clogged, the washer will leak, or you may find standing water in the drum at the end of the cycle. Each drain hose comes with a metal clamp for fastening.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Terry from SIMI VALLEY, CA
Drain hose had a pin hole leak external to washer
Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor). Read more...
Washer Dryer Combo Tub-to-Pump Hose
PartSelect Number PS3617213
Manufacturer Part Number AEM73213001
This is a drain hose assembly for top-load models of LG washing machines. This hose specifically is used to allow water to drain from the tub to the drain pump of the washer. This hose is made of plastic and comes with two clamps to secure it within your washer, one on each end. If you notice your washer is leaking check to make sure if this hose is cracked or damaged, because it will need to be replaced immediately. This drain hose is an OEM part that is sold individually and will require you to disassemble part of your washer to replace it.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Victor from ADDISON, IL
leaking water
Removed the back of the washing machine looked to see where the water was leaking from removed the hose to find a smell crack - ordered a new hose dried up everything with old towels took compressed air and blew off all electrical wires and connectors total time 15 minutes
Read more...
Your Price
$10.34
In Stock
Washer Dryer Combo Plastic Injector Nozzle
PartSelect Number PS11738878
Manufacturer Part Number WP213015
The plastic injector nozzle is used in washers and dryers. It is 3 inches long and is white in color. If your washer is leaking water, replacing the nozzle could solve your problem. For this repair project, you will need a 1/4 nut driver, 3/8 socket with extension, and a stubby Phillips screwdriver. To begin the repair, first remove the front panel by removing screws from the bottom end of both sides. Next, locate the two bolts in the interior of front panel and remove both. Pull bleach dispenser hose off before removing the top cover of washer. Remove clamp that holds the hose to the valve assembly to access the nozzle inside rubber valve and replace with new nozzle. Refer to the instructions provided by the manufacturer for further guidance.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Catherine from Wyandotte, MI
Front load washing machine leaking on floor while in fill mode.
Removed two screws at bottom of front panel and then removed front panel. Then removed two self-tapping bolts (one on each side) holding top panel in place and swung the panel up, out of the way, to expose top of tub and water injection components. Cut off one pinch clamp and loosened screw clamp holding two injector hoses to the injector sleeve. Removed these water injector hoses from injector sleeve assembly which is mounted on top of left side panel upper flange. Replaced deteriorated rubber injector valve, nozzle and the sleeve for the injector (plastic housing containing the injector valve and nozzle). Also replaced deteriorated injector tube seal where injector tube elbow mounts to top of tub assembly. Reinstalled injector hoses with a replacement screw clamp to replace the one cut off. tightened the new clamp and the other, original, screw clamp and checked for leaks. This solved the leakage problem. Secured top panel and re-installed front panel. Hardest part of the task was determining where the leak emanated from but once found and parts ordered, it was a relative snap to fix.
Read more...
Washer Dryer Combo Hose Assembly,Drain
PartSelect Number PS3527325
Manufacturer Part Number 5215ER2002G
The drain hose assembly is a genuine OEM assembly supplied directly by LG for use in washing machines. The assembly includes the hose, connector, elbow fitting, and metal clamp. It is responsible for directing wastewater from the washing machine tub to the household drain or plumbing system. It allows the water to exit the washer efficiently and prevents it from pooling inside the machine at the end of the cycle. If the hose can no longer stay attached to the washer or drainpipe, water is leaking from the hose, or the hose has visible damage such as cracks and splits then you will need to replace it before you can resume using your washer.
Fixes these symptoms
- Leaking
- Will not drain
- See more...
Installation Instructions
Roy C from KNOXVILLE, TN
Moldy smell inside, door boot seal showed signs of mold
Watched several YouTube DIY videos and followed the step by step directions. I also disconnected several other hoses and cleaned them out. Since I live in an hard-water area, deep cleaning may become a 6- month preventative maintenance routine.
Read more...
Your Price
$33.70
In Stock
Washer Dryer Combo Washer Tub-to-Pump Hose
PartSelect Number PS11765836
Manufacturer Part Number W10899966
The tub-to-pump hose carries the water from the tub to the drain pump. Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands
Fixes these symptoms
- Leaking
- See more...
Washer Dryer Combo Hose or Tube Brands
- Crosley Washer Dryer Combo Hoses and Tubes
- Electrolux Washer Dryer Combo Hoses and Tubes
- Frigidaire Washer Dryer Combo Hoses and Tubes
- Jenn-Air Washer Dryer Combo Hoses and Tubes
- Kenmore Washer Dryer Combo Hoses and Tubes
- LG Washer Dryer Combo Hoses and Tubes
- Maytag Washer Dryer Combo Hoses and Tubes
- Whirlpool Washer Dryer Combo Hoses and Tubes