Troy-Bilt Generator Parts

Popular Troy-Bilt Generator Parts

Your Price
$45.30
   Special Order
Troy-Bilt Generator Cap, Fuel Gauge
★★★★★
★★★★★
2 Reviews
PartSelect Number PS9314364
Manufacturer Part Number B4363GS
This OEM replacement fuel gauge cap is designed for use in generators. It comes in a cylindrical shape and has a built-in window to easily view the fuel levels without pulling out the entire cap. It is approximately 5.25 inches in length, while the head has a diameter of 3 inches. The purpose of the cap is to cover and protect the fuel gauge, which indicates the levels of gas available in the tank. It prevents dirt and debris from entering the gauge area and prevents fuel from leaking out. A faulty cap will allow contaminants to enter the gauge, and cause fuel to leak, leading to inaccurate fuel readings and safety risks. Twist the cap to remove it and clean the surrounding area thoroughly. Place the new gauge cap in position and ensure that it is locked in place.
Your Price
$28.63
   In Stock
Troy-Bilt Generator Support-Leg
PartSelect Number PS9940365
Manufacturer Part Number 312510GS
Your Price
$19.31
   On Order
Troy-Bilt Generator Fuel Valve W/Bushing
★★★★★
★★★★★
5 Reviews
PartSelect Number PS8911051
Manufacturer Part Number 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.
Fixes these symptoms
Installation Instructions
James from PICAYUNE, MS
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes. Read more...
Your Price
$5.71
   In Stock
Troy-Bilt Generator BOTTLE, Oil
PartSelect Number PS8817222
Manufacturer Part Number 100005
Your Price
$35.02
   Special Order
Troy-Bilt Generator Solenoid-Starter
★★★★★
★★★★★
3 Reviews
PartSelect Number PS9064363
Manufacturer Part Number 691656
A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other small engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.
Your Price
$5.19
   In Stock
Troy-Bilt Generator Grommet,Tank
PartSelect Number PS9307985
Manufacturer Part Number 83465GS
Installation Instructions
Bruce from CARNATION, WA
Wouldn’t start.
I installed a new solenoid starter. Took me a total of 20 minutes. Started right up. Read more...
Your Price
$59.96
   In Stock
Troy-Bilt Generator Assembly, Handle
PartSelect Number PS8904965
Manufacturer Part Number 189715GS
Your Price
$149.91
   On Order
Troy-Bilt Generator Battery
PartSelect Number PS8908509
Manufacturer Part Number 193043GS
Your Price
$103.61
   In Stock
Troy-Bilt Generator Wheel, 10" Diameter
PartSelect Number PS8914298
Manufacturer Part Number 209636GS
The authentic 10" Wheel Assembly (Wheel, 10" Diameter) is a 10-inch black, plastic-and-ubber wheel. It allows easy moving of the generator. Installation requires pliers and is rated as "Easy". If your tire is flat, then it should be replaced. Refer to your make, model and diagram to ensure this is the right part.
Your Price
$4.99
   In Stock
Troy-Bilt Generator E-Ring
PartSelect Number PS10000220
Manufacturer Part Number 703977
The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.

Troy-Bilt Generator Appliance Types

Related Troy-Bilt Generator Parts

Popular Troy-Bilt Generator Models

Below are the most popular Troy-Bilt Generator models we have. Enter your model number in the search box to find your model.