Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
Samsung Dryer Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Samsung Dryer Parts
- Noisy
- See more...
- Not Heating
- See more...
2. Removed two bolts at bottom front of machine and took off the bottom front panel.
3. Removed three bolts from black plastic exit vent and took it out to give more room to access everything.
4. removed two wires and screws on the limit thermostat. Did the reverse to place the new one.
5. Removed wires (remembering placement), then holder screw. rotated the Gas Dryer Sensor counter clockwise to release the bottom tab so the sensor can be taken off the flame tube. Did the reverse to place the new one on.
6. Removed the one screw on the gas/flame tube that holds the bracket and igniter inside the flame tube. Removed the wires fro the igniter (remember placement) Slid the whole assembly toward the back of the machine to get the tube off the gas valve then rotated the whole assembly counter-clocwise to release the tab on the left side of the bracket. This was a little tight and had to work with it a bit to get the tab out and slide the whole piece out of the flame tube.
7. Once the tube and igniter were out i removed the scree that holds the igniter and replaced with the new one. Made sure no dust, etc. was in the piece.
8. Did the reverse to place the tube/igniter back into the flame tube.
9. Carefully and forcefully removed the wire connectors to the two coils. These were tough to get off. Removed the two screws that hold the bracket that holds the two coils in place. Slid the coils off the spindles remembering which one has the two wire connection and which one has the three wire connection and the way they went on. Replaced the old with the new. Placed the bracket onto the new coils and made sure the little bumps on the top are in the holes in the bracket. Tightened the screws to hold the coil bracket. Reattached the wire connectors to the coils making sure they go ALL the way back on.
10. Vaccumed everything I could to get lint, dust, etc. out.
11.Replaced the black vent plastic.
12 Made sure the exit vent on the back was not crimped or clogged. Checked the little flap door where the vent goes outside to make sure it opens and closes super easy to no air flow is restricted.
13. For testing I left the bottom panel open. Make sure you closed the door, reconnect the plug and turn the gas valve back on. Hit the go button on autodry or timed dry. The door must be closed to create the closed circulation of the system so the fan sucks the flame into the tube otherwise the flame will not fire deep into the tube and will set off one fo the overheat sensors. After hitting the go button your drum will start to rotate, then a few seconds later you'll hear a click and your igniter will start to burn bright orange. Another click and the gas should flow and ignite.
14. This shows that you've fixed the ignition problem. I just replaced everything I thought that could be wrong in stead of hunting and trial and error. All the parts were about $137 so I thought it was worth making sure.
15. IMPORTANT: If during your test the flame turns off after a little while then turns back on only to turn off again, don't panic. This happened to me as well. I found that you need to run the dryer with wet clothes in the dryer. The wetness in the clothes will keep the autodry sensor from shutting off the dryer since there will be moisture in the exhaust. If it's on timed dry the wet clothes will cool the exhaust air and keep the overheat sensors from turning the heat off. So no heating of dry clothes to get out wrinkles. Just dry the wet clothes. This is all I did and it's been working great so far. Good Luck! Read more...
- Drum Not Spinning
- Noisy
- See more...
- Drum Not Spinning
- Noisy
- See more...
- Not Heating
- See more...
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.
Edward Brennan Read more...
- Not Heating
- See more...
Samsung Dryer Appliance Types
Popular Samsung Dryer Models
Below are the most popular Samsung Dryer models we have. Enter your model number in the search box to find your model.
- DV42H5000EW 7.5 Cu. Ft. 9-Cycle Electric Dryer - White
- DV42H5000EW 7.5 Cu. Ft. 9-Cycle Electric Dryer - White
- DV42H5000EW Samsung Dv42h5000ew/A3-02 Dryer
- DV42H5000EW DRYER
- DV42H5000EW Samsung Dv42h5000ew/A3-03 Dryer
- DV42H5000EW 7.5 Cu. Ft. 9-Cycle Electric Dryer
- DV42H5000EW Samsung Dv42h5000ew/A3-00 Dryer
- DV42H5000EW Samsung Dv42h5000ew/A3-01 Dryer
- DV42H5000EW Samsung Dryer Dv42h5000ew/Ac-0000
- DV42H5000EW 7.5 Cu. Ft. 9-Cycle Electric Dryer - White
- DV42H5000EW DRYER
- DV42H5000EW 7.5 Cu. Ft. 9-Cycle Electric Dryer - White
- DV42H5000EW DRYER
- DV42H5000EW Dryer
- DV42H5000EW DRYER
- DV45H7000EW 7.4 Cu. Ft. 9-Cycle Electric Dryer - White
- DV45H7000EW DRYER
- DV45H7000EW DRYER
- DV45H7000EW Samsung Dryer Dv45h7000ew/A2
- DV45H7000EW Samsung Dv45h7000ew/A2-00 Dryer