Washer Wheels and Rollers

Popular Washer Wheels and Rollers

Your Price
$57.93
  In Stock
Washer Glide and Spring Kit
★★★★★
★★★★★
6 Reviews
PartSelect Number PS2017149
Manufacturer Part Number 205000
This glide and spring kit contains two three inch springs, four one inch square glides, and two tubes springs. This kit replaces older style round roller glides.
Fixes these symptoms
  • Burning smell
  • Spins slowly
  • Will not agitate
  • See more...
Installation Instructions
dominic from weirton, WV
The belts were not staying tight enough to agitate properly.
Firstly, remove ac power from washer!
After removing the front panel of the washer (two philips screws), I loosened and removed the plastic motor cover and removed three hex head screws holding the motor. Have someone help you tilt the washer so you can remove the belts by "rolling" them off of the pullies (pump pully and motor pully). What I did was use a chemical degreaser to clean the motor base metal channel where the nylon sliders reside. After doing that and letting it dry, I removed the two old
springs. I ended up reinstalling the old springs because they were not stretched and I installed a new spring (total three) on the right side of the mount. A stiff metal rod with a hook on the end will help you install the springs. Squirt some of the included silicone lubricant on both sides of the motor mount channel and exercise the lube. Reinstall the motor and plastic cover over top of motor. Clean hands and clean belts while you have them out, reinstall belts and front cover and you're finished. My wife said it never ran better!
Read more...
Your Price
$19.85
  In Stock
Washer Mounting Strip Wheel
★★★★★
★★★★★
1 Review
PartSelect Number PS11747645
Manufacturer Part Number WP99002106
This white mounting strip wheel is a little over an inch in diameter.
Installation Instructions
Wanda from Bay Shore, NY
loose top basket/
I had two problems with the dishwasher. The top basket was loose, but the main problem was a plastic part inside the bottom assembly.

The part was backordered, so I re-ordered it through Sears. They said it would arrive in two days. Theirs came in two weeks, and their customer service was terrible.

Your "backordered" part came in two days, even before it was supposed to come had the part not been back ordered. I am delighted with your customer service and your company.

The illustrations on your website were excellent. They helped us not only to identify the part, but to diagnose the problem.

This was my first purchase through your company and if I ever need parts again, there is absolutely no reason to go anywhere else.

You have an excellent company, and great website! I bookmarked your page for future purchases.
Read more...
Your Price
$9.75
  In Stock
Washer ROLLER
PartSelect Number PS1155768
Manufacturer Part Number 280160
Your Price
$65.55
  In Stock
Washer Idler Pulley Shaft
PartSelect Number PS11742857
Manufacturer Part Number WP56461
This shaft is made to fit the center of the idler pulley wheel of many clothes dryers. It is less than two inches long, and is made of metal.
Fixes these symptoms
Installation Instructions
Brian from Yucaipa, CA
Screeching sound coming from back of the dryer.
First removed the bottom access panel, then the then pried the top lid open. Then, I could get to the four screws holding the front of the drum in place. Once that was removed, reached underneath drum and disconnected belt from tensioner pulley and motor. Removed the drum and discovered the problem. One of the two drum rollers had completely disintergrated from the shaft, actually "melting" off of its roller shaft. Removed both of the rollers and shafts by putting a flathead screwdriver on the slot of the shaft, and at the same time holding the locknut behind the bracket with a box wrench. I replaced both shafts and rollers and reused the same washers and snaprings. I used a screwdriver and a vice to remove the snap rings off of the old shafts. The best bet is to use a pair of snap ring pliers, which I didn't have. I used some white silicone grease to lube the new rollers up, reinstalled them and replaced the belt. You MUST route the belt around the drum before you install, then connect the belt to the motor underneath and wrap it around the tensioner. While I had everything opened up, I shop-vac"d the inside of my dryer(filthy). I did this before putting anything back together. Also, when re-installing the front dryer panel, make sure the motor inlet and the lint outlet tube form an airtight seal. All in all, this was a fairly strightforward job. The dryer now works great and is as quiet as a mouse. Read more...
Your Price
$270.47
  Special Order
Washer Drum Pulley
PartSelect Number PS269309
Manufacturer Part Number WH07X10004
Your Price
$42.54
  Special Order
Washer ROLLER
PartSelect Number PS270960
Manufacturer Part Number WH1X2560
Your Price
$51.37
  Special Order
Washer WHEEL
PartSelect Number PS2324866
Manufacturer Part Number 8183268
Your Price
$37.51
  Special Order
Washer ROLLER
PartSelect Number PS465365
Manufacturer Part Number 5303308081
Your Price
$27.00
  Special Order
Washer WHEEL
PartSelect Number PS474161
Manufacturer Part Number 5308015145