Washer Seals and Gaskets
Popular Washer Seals and Gaskets
Your Price
$34.77
In Stock
Washer Upper Drum Glide
What I would add to previous reviews is to pull the front off or the little acces grill in back and check to see what kind of belt you have. According to the model #, It showed the wide flat belt when in fact I had the smaller ribbed belt. Glad I checked before ordering.
A few things that will make your life easier is once you have the old upper guide/seal removed, put down the glue then use several med sized plastic spring clamps to hold the seal in place while the glue sets up, (@ 20-30 min). Their cheap and you should have some around anyway. When replacing the seals I would go ahead and replace the belt too. It's cheap and if your machine is 5+ yrs old probably is worn. Total cost of repair was about $60 (inc shipping). Took about 1 hr 20 min total time. Most of that time was scrapping the old seal material/ glue off the dryer front. Actual disassembly and repair maybe 1/2 hour. Other little tip is the clips for the lid of dryer is to use a flat screwdriver and gently push straight in until it's compressed enough to release the lid, it will pop up when pushed in far enough. That one took me a while to figure out.
Thanks to Part Select for such a helpful site. My dryer is like new again. Read more...
PartSelect Number PS470317
Manufacturer Part Number 5303937139
The upper drum glide is attached to the front panel of your dryer, you can locate it by removing the top portion of your dryer. The drum glide allows the drum to rotate with ease and little sound. The front upper felt glide pad with three nylon glides also includes adhesive, essential for mounting accurately. For this project you will need a putty knife, Phillips screwdriver, and a wire brush. This repair is meant to fix issues such as an abnormal amount of noise or the dryer not tumbling as it should. Consider replacing your belt at the same time if you have a dryer more than 5 years old, as it is likely worn.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Matthew from Portland, OR
Clothes getting scorch marks, drum noise
First and foremost, I read the repair reviews here at parts source and found that a) Other people had the same symptoms, b)following their repair tips made it super easy.What I would add to previous reviews is to pull the front off or the little acces grill in back and check to see what kind of belt you have. According to the model #, It showed the wide flat belt when in fact I had the smaller ribbed belt. Glad I checked before ordering.
A few things that will make your life easier is once you have the old upper guide/seal removed, put down the glue then use several med sized plastic spring clamps to hold the seal in place while the glue sets up, (@ 20-30 min). Their cheap and you should have some around anyway. When replacing the seals I would go ahead and replace the belt too. It's cheap and if your machine is 5+ yrs old probably is worn. Total cost of repair was about $60 (inc shipping). Took about 1 hr 20 min total time. Most of that time was scrapping the old seal material/ glue off the dryer front. Actual disassembly and repair maybe 1/2 hour. Other little tip is the clips for the lid of dryer is to use a flat screwdriver and gently push straight in until it's compressed enough to release the lid, it will pop up when pushed in far enough. That one took me a while to figure out.
Thanks to Part Select for such a helpful site. My dryer is like new again. Read more...
Washer Front Load Bellow
PartSelect Number PS12074757
Manufacturer Part Number W11106747
This is a door bellow, also known as a door seal gasket, made for various models of washing machine. This bellow is designed to seal the inner drum of the washer from the outside of the washing machine and its internal components. If your washer is currently experiencing issues with leaking, this gasket is likely worn out and in need of replacing. This gasket is made of gray rubber and is sold as an individual OEM part and is sold separately from its necessary clamp.
Fixes these symptoms
- Leaking
- Marks left on clothes
- See more...
Your Price
$5.77
In Stock
Washer Centerpost Gasket
PartSelect Number PS11723081
Manufacturer Part Number W10814296
This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edge, black in color, and made of plastic material. To perform this repair, you will need to disconnect the power, drain hose, and the inlet hose. You will need to remove the entire outside cabinet to have access to the tub assembly. The tub will need to be removed entirely. This is a genuine part that is sourced directly from the manufacturer.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go.
Read more...
Washer Door Boot Seal
PartSelect Number PS3535210
Manufacturer Part Number MDS47123602
This door boot is for washers.
Door boot forms a seal between the wash tub and the door, preventing leaks.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Matt from ROYAL OAK, MI
Replaced the washer door gasket
Followed the videos on line. However instead of buying the $75 spring expansion tool I used two zip ties. One at each end of the spring to create loops for my index fingers to pull the spring apart. Needed a second person to help hold the ring in place at 3&9 position.
Read more...
Your Price
$19.62
In Stock
Washer Front Upper Felt Seal with Adhesive
Replaced the slider felt on the drum and the belt since i had it apart. Also replaced the seal from the front panel to the blower motor.. while it was apart i cleaned the inside with bleach and a rag. reasembled a tryed it out. Run like a new dryer- Nice and quiet.- It had been sqeeking for months before the it stopped working. the time it took to fix it was a lot less hassle than it would have been to buy a new and get rid of the old one. And it saved me money. I love saving money!! I would recomend partsselec.com t.good prices,fast shipping, got what i needed. What more can you ask for.. Read more...
PartSelect Number PS832644
Manufacturer Part Number 5303937182
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so that heat remains in the dryer while it tumbles. If your old upper felt seal is coming apart, you notice that hot air is leaking out the dryer door, or your clothes are taking too long to dry, you may need to replace the seal. When you order this part, it comes with the upper felt seal, as well as the required high-temperature adhesive.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Zaya from Weaverville, CA
Rear bearing assembly failed and damage heating element
Removed top using a butter knife to release the two tabs in the front(between the top and the front). Removed the front(two screws from the inside. removed rear louver panel(four screws). reached in through rear panel and released belt. removed drum assembly and change out, bearing assembly drum and bushing assembly in the back panel, being sure not to forget the grounding bearing(had my 9 year old give me an extra hand to hold the ball bearing on the back..Replaced the slider felt on the drum and the belt since i had it apart. Also replaced the seal from the front panel to the blower motor.. while it was apart i cleaned the inside with bleach and a rag. reasembled a tryed it out. Run like a new dryer- Nice and quiet.- It had been sqeeking for months before the it stopped working. the time it took to fix it was a lot less hassle than it would have been to buy a new and get rid of the old one. And it saved me money. I love saving money!! I would recomend partsselec.com t.good prices,fast shipping, got what i needed. What more can you ask for.. Read more...
Your Price
$16.71
In Stock
Washer Tub Seal
I also power washed the basket and tub before reassembly.
The tub seal comes with the transmission and brake assembly so it's not necessary to order another seal.
The agitator coupling kit contains a redesigned coupler and longer screw with new o-ring.
I bought the hub nut, split ring, tub bearing, agitator coupling kit and washer hub because these are all the parts that go on the transmission shaft. I felt it was best to spend a few dollars more to replace every part involved with the spin and agitation of the washer.
I used the channel lock and a hammer with a shortened handle to remove and replace the hub nut. Use caution as the nut is aluminum.
The entire job took 5 hours. Read more...
PartSelect Number PS4704237
Manufacturer Part Number WH02X10383
The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at agitation time, your tub seal may need to be replaced. You can check if the tub seal needs to be replaced by watching that area during an actual fill cycle. Take off the front panel, or if it is a front-loading washer, the rear panel. Without touching the washing machine, observe the place where the shaft of the transmission comes into the tub and the weep holes at the housing of the rear bearing. If there is water leaking, the tub seal is at fault.
NOTE: This seal is difficult to replace and should probably be installed by a qualified technician.
Fixes these symptoms
- Leaking
- Marks left on clothes
- Will not agitate
- See more...
Installation Instructions
Wayne from Saint Augustine, FL
Tub seal leaked, rusted the transmission bearing which locked up
I followed the instructions in the GE Consumer Service Training Technician Manual Pub. No. 31-10008. I also power washed the basket and tub before reassembly.
The tub seal comes with the transmission and brake assembly so it's not necessary to order another seal.
The agitator coupling kit contains a redesigned coupler and longer screw with new o-ring.
I bought the hub nut, split ring, tub bearing, agitator coupling kit and washer hub because these are all the parts that go on the transmission shaft. I felt it was best to spend a few dollars more to replace every part involved with the spin and agitation of the washer.
I used the channel lock and a hammer with a shortened handle to remove and replace the hub nut. Use caution as the nut is aluminum.
The entire job took 5 hours. Read more...
Washer Door Boot Seal
BUY THE TOOL! Buy the spring expander tool. I tried with needle nose and bloodied my knuckles. I am sure you all are strong and more adept, but next time I will buy the tool. Read more...
PartSelect Number PS3524977
Manufacturer Part Number 4986ER0004F
Also known as a door boot seal or bellow and comes with a drain hole. Door boot 4986ER0004F is an original equipment manufacturer (OEM) part that fits some front-load washers in these series: Kenmore and Kenmore Elite 796; and LG WM and CW.
Door boot 4986ER0004F forms a seal between the wash tub and the door, preventing leaks.
This door boot includes a drain port; if your 27-inch LG front-load washer was made before September 2007, use door boot 4986ER0004B instead, because those washers don't have a drain port.
Fixes these symptoms
- Burning smell
- Leaking
- Marks left on clothes
- See more...
Installation Instructions
Andrew from BOTHELL, WA
Door gasket had hole
Removed and replaced. BUT...BUY THE TOOL! Buy the spring expander tool. I tried with needle nose and bloodied my knuckles. I am sure you all are strong and more adept, but next time I will buy the tool. Read more...
Your Price
$7.68
In Stock
Washer
PartSelect Number PS11742027
Manufacturer Part Number WP3949550
This part goes on the agitator retaining bolt.
Fixes these symptoms
- Leaking
- Will not agitate
- See more...
Installation Instructions
Patrick from Marysville, WA
The upper agitator arm would not rotate
It was extremely easy. I removed the plastic cap under the softener dispenser, removed the nut and washer that holds the upper agitator in place and then replaced the parts that came in the kit. The most important note for those who may be doing this job is that the o-ring for the cap under the softener dispenser, the seal washer for the bolt and the thrust spacer under the upper agitator all came with the kit. I did not realize that and ordered them all seperately.
Read more...
Your Price
$126.38
In Stock
Washer Front Load Bellow Door Boot Seal - Gray
The only difficult part was putting the outside band clamp on over the bellow without it slipping out of place - took a few tries. The video was very helpful - I did put hardware into plastic bags based on the steps in the removal for so that I wouldn't forget (or get them mixed up).
I was able to do this project while home from work with a sick kindergartener. Problem started and did the removal the first day ordered the part and it arrived 2 days later - install complete in less than an hour. We went back to school/work with a operating washer by the end of the week! Thank you - it was actually kinda fun and my son bragged to his grandfather that 'he and momma fixed the washer'. Read more...
PartSelect Number PS11753988
Manufacturer Part Number WPW10381562
This door boot, also known as a door seal, is compatible with various models of front load washing machines. It is a genuine OEM replacement part that is sourced directly from the manufacturer to ensure the best fit with your appliance. The door boot is made of rubber, and it is responsible for creating a tight seal between the tub and the door to prevent water and detergent from leaking out of the washer when it is in use. This helps to prevent injuries and ensure the efficient running of the appliance. It is common for the door boot to wear down over time. It will need to be replaced if it can no longer securely fit around the door frame or if it is torn or cracked.
Fixes these symptoms
- Burning smell
- Leaking
- Marks left on clothes
- See more...
Installation Instructions
Laura from WAYLAND, MA
Washer leaking - noticed large crack in the seam of the bellow
9 year old washer started leaking - after inspecting noticed a large hole in the bellow. The only difficult part was putting the outside band clamp on over the bellow without it slipping out of place - took a few tries. The video was very helpful - I did put hardware into plastic bags based on the steps in the removal for so that I wouldn't forget (or get them mixed up).
I was able to do this project while home from work with a sick kindergartener. Problem started and did the removal the first day ordered the part and it arrived 2 days later - install complete in less than an hour. We went back to school/work with a operating washer by the end of the week! Thank you - it was actually kinda fun and my son bragged to his grandfather that 'he and momma fixed the washer'. Read more...
13% OFF
Your Price
$156.13
$179.55
In Stock
Washer Door Bellow
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow.
Use a small screwdriver or other to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.
The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily.
When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow.
Push as much of the bellow into the washer as possible to get it out of the way.
Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and the secures it to the portion that holds the basket.
This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way.
Loosen the hose clamp almost all of the way, not necessary to have the hose clamp come completely apart.
You can now remove the entire hose clamp from around the bellow by pulling it forward.
You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out.
Pull the old bellow completely out, very easy to do.
Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side.
You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.
Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force.
As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.
Now it is time to install the Hose clamp. Un bend anything that might have bent on the clamp. With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop.
Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.
Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. This w Read more...
PartSelect Number PS11744957
Manufacturer Part Number WP8182119
This is a door bellow, also known as a door gasket or seal, that is compatible with washing machines. Door bellows are used as a method to seal the inner drum of the washing machine and the soapy water inside it, from the rest of the washer cabinet and your home. If you notice any leaks at the front of your washing machine, this door bellow may be worn out or damaged, so inspect it to ensure it needs replacing. This door bellow is made of a thick rubberized material and wraps around the inner drum and will need a clamp to stay secure. This door bellow is sold as an individual OEM part and is not sold with any other parts or accessories.
Fixes these symptoms
- Leaking
- Marks left on clothes
- See more...
Installation Instructions
Franck from Annandale, VA
Bellows were moldy, needed to replace
The first step is to remove the retainer ring that holds the outside of the bellow in place.To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow.
Use a small screwdriver or other to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.
The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily.
When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow.
Push as much of the bellow into the washer as possible to get it out of the way.
Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and the secures it to the portion that holds the basket.
This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way.
Loosen the hose clamp almost all of the way, not necessary to have the hose clamp come completely apart.
You can now remove the entire hose clamp from around the bellow by pulling it forward.
You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out.
Pull the old bellow completely out, very easy to do.
Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side.
You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.
Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force.
As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.
Now it is time to install the Hose clamp. Un bend anything that might have bent on the clamp. With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop.
Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.
Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. This w Read more...
Washer Seal or Gasket Brands
- Admiral Washer Seals and Gaskets
- Amana Washer Seals and Gaskets
- Crosley Washer Seals and Gaskets
- Electrolux Washer Seals and Gaskets
- Estate Washer Seals and Gaskets
- Frigidaire Washer Seals and Gaskets
- General Electric Washer Seals and Gaskets
- Gibson Washer Seals and Gaskets
- Haier Washer Seals and Gaskets
- Inglis Washer Seals and Gaskets
- Kenmore Washer Seals and Gaskets
- KitchenAid Washer Seals and Gaskets
- LG Washer Seals and Gaskets
- Magic Chef Washer Seals and Gaskets
- Maytag Washer Seals and Gaskets
- Roper Washer Seals and Gaskets
- Tappan Washer Seals and Gaskets
- Westinghouse Washer Seals and Gaskets
- Westinghouse Washer Seals and Gaskets
- Whirlpool Washer Seals and Gaskets