Range Brackets and Flanges
Popular Range Brackets and Flanges
Your Price
$155.28
In Stock
Range Dual surface element switch
PartSelect Number PS3504401
Manufacturer Part Number 316238201
This switch controls the stove top surface burner. This surface element control switch is for ranges.
Surface element control switch turns the surface element on and off and controls how much heat the element produces.
Unplug the range or shut off the house circuit breaker for the range before installing this part.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Miguel from PLANT CITY, FL
The front left dual element stopped regulating temperature
Replaced the dual element switch and that fixed it up
Read more...
Your Price
$16.66
In Stock
Range Single Heating Element Support Clip
I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support. Read more...
PartSelect Number PS243701
Manufacturer Part Number WB2X9719
The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this replacement should be the solution. The tools needed for this project are slip joint pliers. For safety precautions, make sure to unplug your range from the power source, or shut off the house circuit breaker before starting this project. Refer to the installation instructions for best results and accuracy.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Paul from Canton, NY
broiling element had burned through, req. its replacement
First I removed the two screws that hold the element in place. I also removed a screw that held one end of a support bracket. I then pulled the element out about 3 inches and disconnected the two wires. Reversing these steps, I finished the element's replacement.I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support. Read more...
Range Anti-Tip Kit
PartSelect Number PS3655242
Manufacturer Part Number 316112005
The anti-tip bracket kit comes with one metal bracket and two installation screws, and is sourced directly from the genuine manufacturer. It prevents the freestanding oven, range, or stove from tipping when force or weight is applied to an open oven door. The bracket is secured to the floor and wall and fits over the rear leveling leg in the back of the appliance, in a cutout specifically designed for the anti-tip bracket. This part is very essential to the safe operation of the appliance. Failure to install the bracket properly can result in the oven tipping or falling and causing injuries.
Installation Instructions
Brian from Panama City Beach, FL
anti-tip bracket not installed
I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.
Read more...
Range Mounting Plate
PartSelect Number PS7784808
Manufacturer Part Number 3300W0A045A
This mounting plate is a manufacturer-approved replacement part for your microwave. The mounting plate, or bracket, secures your above-range microwave in place against the wall. To conduct this repair, make sure to first disconnect the power source, and wear protective gloves.
Installation Instructions
Jeffrey from San Antonio, TX
Metric
Owners manual list 1/4 which was sent for the mounting bolts. They don't fit. This unit required metric. Don't try to force the bolts, just match to closest metric.
Read more...
Range Bearing Retainer
Remove 2 screws that held the top on the dryer.
Removed the 2 screw that held the front on the dryer.
Unhooked the belt from the tensioner and motor pulley.
Pulled the drum out. Removed the belt.
Removed the three screws that held the bearing assembly
on the back of the drum.
Removed the keeper o-ring slide the bad bearing off of shaft. Slide the new bearing on the shaft put the new o-ring on the shaft. Reassembled the bearing on back of the drum. Put belt back around the drum and put drum back in place. Put The belt around the motor pulley and tensioner
(this is probably the hardest part).
Put the front and top back together.
Turned the power back on. Job done Read more...
PartSelect Number PS266696
Manufacturer Part Number WE1M300
There is a slot in it for a ground strap.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Kerry from New Martinsville, WV
Noisy like a chain rattling inside
Disconnect Power from the DryerRemove 2 screws that held the top on the dryer.
Removed the 2 screw that held the front on the dryer.
Unhooked the belt from the tensioner and motor pulley.
Pulled the drum out. Removed the belt.
Removed the three screws that held the bearing assembly
on the back of the drum.
Removed the keeper o-ring slide the bad bearing off of shaft. Slide the new bearing on the shaft put the new o-ring on the shaft. Reassembled the bearing on back of the drum. Put belt back around the drum and put drum back in place. Put The belt around the motor pulley and tensioner
(this is probably the hardest part).
Put the front and top back together.
Turned the power back on. Job done Read more...
Range STACK KIT FOR LONG VENT DRYER
PartSelect Number PS12069913
Manufacturer Part Number W10869845
Installation Instructions
Nelson from Middletown, NY
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Read more...
Range Bracket or Flange Brands
- Amana Range Brackets and Flanges
- Bosch Range Brackets and Flanges
- Crosley Range Brackets and Flanges
- Electrolux Range Brackets and Flanges
- Frigidaire Range Brackets and Flanges
- Gaggenau Range Brackets and Flanges
- General Electric Range Brackets and Flanges
- Gibson Range Brackets and Flanges
- Hotpoint Range Brackets and Flanges
- Jenn-Air Range Brackets and Flanges
- Kelvinator Range Brackets and Flanges
- Kenmore Range Brackets and Flanges
- KitchenAid Range Brackets and Flanges
- LG Range Brackets and Flanges
- Maytag Range Brackets and Flanges
- Tappan Range Brackets and Flanges
- Thermador Range Brackets and Flanges
- Uni Range Brackets and Flanges
- Westinghouse Range Brackets and Flanges
- Westinghouse Range Brackets and Flanges
- Whirlpool Range Brackets and Flanges