Part Location Diagram of DC47-00019A Samsung Heating Element - 5300W
See part NI in the diagram
Replacing your Samsung Dryer Heating Element - 5300W
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Heating Element - 5300W DC47-00019A

★★★★★
★★★★★
17 Reviews

Rated by 5 customers 

A Bit Difficult 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

13% OFF
$ 89.61 $ 103.05
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

Does this part fit my model?

Need help finding your model number?
PartSelect Number PS4205218
Manufacturer Part Number DC47-00019A
Manufactured by Samsung for Samsung, Maytag, Kenmore, Amana
Product Description

Heating Element - 5300W Specifications

This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Samsung Dryer Heating Element - 5300W

Replacing your Samsung Dryer Heating Element - 5300W
Troubleshooting
This part fixes the following symptoms:
Not Heating
This part works with the following products:
Dryer.
Part# DC47-00019A replaces these:
AP4201899, DC47-00019A
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
17 Reviews
4.7
Filter By Rating:
  • 5 Stars
    15
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    1
Sort by:
  • 1
  • 2
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
  • 2
Customer Repair Stories
 Average Repair Rating: 2.2 / 5.0, 5 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
Timed dryer cycle was stuck on 1 minute, dryer wouldn't stop running unless door was opened.
Issue was the heating element coil, which had broken in places and shorted itself out. I removed the top and front panels to expose the heating element's housing. Then unplugged, removed and disassembled the housing to expose the heating element (there are many videos online that explain the process). Once the heating element was replaced, the problem disappeared. Now the clothes are drying much faster than before. It is definitely worth getting the Samsung OEM part. Many reviews on generic equivalents were negative, despite how attractive the low price may look at first. PartSelect has never failed to impress with quick shipping and quality products.
  • Joseph from REHOBOTH, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned Heating element
See Utube.com
Other Parts Used:
Heating Element - 5300W Thermal Fuse
  • John from SACRAMENTO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no heat during cycle
Son in law followed youtube video and installed both parts.

Do you really want to know how it went? It quit heating in the first five minutes

My new dryer was just installed this evening.

Case closed
Other Parts Used:
Heating Element - 5300W Thermal Fuse
  • Diana from LYLE, WA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer wasn’t heating
Well it went really well until the dryer was put back together as it still didn’t heat. The dryer was taken apart again. This time the thermistors &fuse was tested. Alas, the new fuse was faulty. After putting the car lid fuse back on n, the dryer worked again
Other Parts Used:
Heating Element - 5300W Thermal Fuse Thermistor
  • Cynthia from JOHNSTOWN, NY
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers
21 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Heat
Have to remove top panel (screws on upper back), then control panel (screws on front), then front panel and door (screws on front). Good Luck, watch for sharp edges.
Other Parts Used:
Heating Element - 5300W Thermal Fuse Thermistor
  • Joel from SOUTH SALEM, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
9 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

12 questions answered by our experts.
Sort by:
  • 1
  • 2
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joe
October 27, 2017
My Samsung dryer has no heat. It is running fine and has no error code, just no heat! Is it the heating element or possibly something else?
For model number DV210AEW/XAA
PartSelect logo
Hi Joe, Thank you for the question. I suggest testing the thermostats and fuses on the element and blower housing with a multi meter to see if one of them are defective. The elements do not normally go. It is more then likely a thermostat or thermal fuse. Hope this helps!

26 people found this helpful.

Was this helpful?
Thank you for voting!
Janet
November 19, 2017
My Samsung dryer has no heat. It is running fine and has no error code, just no heat! Is it the heating element or possibly something else?Thank you.
For model number DV350AER/XAA
PartSelect logo
Hi Janet, Thank you for the question. There are a few parts you can test with a multi meter before replacing the element. The thermostat and Bracket assembly PartSelect Number PS4276292 and the High Limit Thermostat ,PartSelect Number PS4205217 on the element housing. In most cases one or both of these parts would need to be replaced when you have no heat.Usually if the element has burnt out you will see physical damage to the element.Hope this helps!

13 people found this helpful.

Was this helpful?
Thank you for voting!
Edward
April 9, 2019
How do you check heat element
For model number 402.89032010
PartSelect logo
Hi Edward, thank you for your question. To test your heating element you can test that with a multi meter and it should be reading between 0 - 50 ohms. I hope that helps. Good luck with your repair.

7 people found this helpful.

Was this helpful?
Thank you for voting!
Josie Woods
August 22, 2017
My dryer starts and then goes off. Error code he appears. Samsung service says the error code means heating element, but after reading the description of what this part is suppose to solve (if the heating element is burned, dryer does not heat or over heats, or clothes take to long to dry), the dryer does not stay on and an error code comes up. Is this in line with what occurs with this part #ps4205218 manufactory part #dc47 00019a? Thank you for your reply
For model number DX218AEW/XAA
PartSelect logo
Hi Josie, Thank you for your inquiry. Yes, the HE error code is in relation to the heating element not working correctly. If your are getting the HE error code and the dryer is shutting off, see if the circuit breaker for the dryer has been tripped. If so, you will need to unplug the dryer and check the wire connections between the electronic control board and the heating element. If there are any loose wires reconnect them. If the wire harness or the heating element appears damaged replace them. I hope this helps. Thank you and have a great day!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Dewane
February 20, 2018
Does this dryer have a heater element ? If yes can you give me part # , thanks
For model number Dv331aew/xaa
PartSelect logo
Hello Dewane, thank you for your question. I have researched the model you have provided and have found the part you’re looking for is Heating Element Part Number DC47-00019A. Good luck with your repair!

3 people found this helpful.

Was this helpful?
Thank you for voting!
John
October 14, 2019
Dryer runs but does not heat up
For model number DV42H5200EF/A3
PartSelect logo
Hello John, thank you for writing. This is likely due to either a faulty Thermistor, part number PS4204984, or Heating Element, this part number PS4205218 for your model. Good luck with your repair!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Calvin
January 31, 2019
My dryer is running but it isn't producing any heat. I replaced the heating element last year. Should i replace it again?
For model number DV50F9A7EVP/A2
PartSelect logo
Hello Calvin, thank you for your question. The heating element rarely goes bad. I would recommend testing the thermostats and fuse to determine if one of those parts are faulty. A faulty thermostat can cause the unit to run, but not heat. Testing the thermostats is a very easy job. Set your multimeter to the R X 1 setting. Take each of your meter's probes and touch one to each terminal. You are testing for continuity, and you should receive a reading of either zero or infinity. At room temperature, testing the thermostat should produce a reading of zero. But if a thermostat is tested when it is heated to its limit, a reading of infinity should be produced. We strongly recommend that you test your thermostat at room temperature. If the test you conduct with your thermostat does not produce these results, then you should replace the component. If the thermostats are tested and are fine, the element should be replaced. I hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Sunila
May 15, 2019
Our Samsung dryer runs and dries the clothes but they come out super hot and when finished it keeps beeping with he error code. Can you please advise the part numbers that could be faulty in this situation. Thanks!
For model number DV42H5000EW
PartSelect logo
Hello Sunila, Thank you for the question. The HE error code means there is a Heating Error. Make sure the gas supply cut-off valve for the dryer is fully open. Unplug the dryer and reconnect any loose wiring connections on the gas valve coils. Replace the wire harness if damaged. Hope this helps!

Was this helpful?
Thank you for voting!
Willians
April 26, 2019
I got the heat element from part select, i installed but now i don’t see any song of power on machine. What can be wrong?
For model number DV42H5400EW
PartSelect logo
Hi Willians, thank you for your question. Looking at your model information there are a few parts that you should take out and test to see which one is giving you the issue. The first parts to check in this case would be all of your thermostats and thermal fuses. You can test those parts with a multi meter and they should be reading 0 ohms to be working correctly. Something else you should also check would be your filter and ducts. Make sure there is absolutely no blockage that would restrict air flow in your appliance. If all of those parts are fine then the issue might actually be in your control board. I hope that helps. Good luck with your repair.

Was this helpful?
Thank you for voting!
Jason
December 19, 2017
What is difference between part no. Dc97-14486a and dc47-0019a?
For model number DV218AEB/XAA-0000
PartSelect logo
Hi Jason, Thank you for your question. This part is just your heating element. Part: Dc97-14486a is the metal duct around your heating element. I hope that helps. Good luck with your repair.

Was this helpful?
Thank you for voting!
  • 1
  • 2
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS4205218
Manufacturer Part Number: DC47-00019A
Brand
Model Number
Description
Kenmore
40289032010
Dryer - DRYER
Kenmore
40289032011
Dryer - DRYER
Kenmore
40289032012
Dryer - DRYER
Samsung
59289622
Dryer - Dryer
Samsung
59289653
Dryer - Dryer
Samsung
DV203AES
Dryer - Samsung Dryer Model DV203AES Parts
Samsung
DV203AEW
Dryer - DRYER
Samsung
DV203AEW/XAA-0000
Dryer
Samsung
DV203AEWXAA
Dryer - Samsung Dryer Model DV203AEWXAA Parts
Samsung
DV206AES
Dryer - Samsung Dryer Dv206aes
Samsung
DV206AESXAA
Dryer - Samsung Dryer Model DV206AESXAA Parts
Samsung
DV206LEW
Dryer - Samsung Dryer Model DV206LEW Parts
Samsung
DV206LEWXAC
Dryer - Samsung Dryer Model DV206LEWXAC Parts
Samsung
DV209AEW
Dryer - DRYER
Samsung
DV209AEW/XAA-0000
Dryer
Samsung
DV209AEWXAA
Dryer - Samsung Dryer Model DV209AEWXAA Parts
Samsung
DV210AES
Dryer - Samsung Dryer Model DV210AES Parts
Samsung
DV210AESXAC
Dryer - Samsung Dryer Model DV210AESXAC Parts
Samsung
DV210AEW
Dryer - DRYER
Samsung
DV210AEW/XAA
Dryer
Samsung
DV210AEWXAC
Dryer - Samsung Dryer Model DV210AEWXAC Parts
Samsung
DV218AEB
Dryer - DRYER
Samsung
DV218AEB/XAA-0000
Dryer
Samsung
DV218AEBXAA
Dryer - Samsung Dryer Model DV218AEBXAA Parts
Samsung
DV218AES
Dryer - Samsung Dryer Model DV218AES Parts
Samsung
DV218AESXAC
Dryer - Samsung Dryer Model DV218AESXAC Parts
Samsung
DV218AEW
Dryer - DRYER
Samsung
DV218AEW/XAA-0000
Dryer
Samsung
DV218AEWXAA
Dryer - Samsung Dryer Model DV218AEWXAA Parts
Samsung
DV219AEB
Dryer - DRYER
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service