This 5/16-18 wing knob is sold individually. It is a plastic part, black in color, that works on a variety of equipment. Its general function is to allow you to quickly loosen, remove, or fold down th...
This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for...
This quarter-inch Nylock nut, or hex nut, is silver in color and sold individually. Made of metal, its simple task is to secure and lock parts in place on a variety of different equipment. Regardless ...
This bolt is a genuine OEM replacement part used in a variety of lawn and garden equipment. It is 2 inches long with a head diameter of 5/16 inches, and a thread pitch of 16 threads per inch. The bolt...
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Norman
December 8, 2023
Chute rotation; spins and does not engage gear ring
For model number SS7522E
Hello Norman, thank you for contacting us. Based on our understanding of the issue, we would suggest replacing the single stage chute rotation kit, part number PS11836831, to solve the problem. Glad to be of help!
Removed scraper bar and support. Removed flight paddles. Several retaining screws were seized requiring WD-40 and vice grips for removal. Torx sockets stripped out due to threads being seized. Hex head cap screws would be better for both scraper bar and flight papples.once the screws were removed I used a tap to clean the threads and appl
... Read moreied lubricant to minimize future corrosion. Three of the four lock nuts for the scraper bar were either not included or lost in shipping due to poor packing requiring me to purchase replacements. Overall, the job took longer than it should have due to the additional time required to remove seized screws and acquire replacement lock nuts.
NOTES: 1) This is not a new model, but a rebranded version - previously under Murray, Simpliticy, Snapper, etc., so parts are available, but not readily identified yet. 2) This repair may be quite simple or it may be a huge problem, depending on whether the manufacturing problem described below is present. 3) The space between t
... Read morehe housing and aluminum pulley is so tight that a belt CANNOT be fit through it! Therefore, the only way to replace the belt is to remove the pulley. * * * * * * * * * * * * * * * * * * Step 1. As with every other single stage snow blower, remove the belt cover held by six 10 mm bolts. This may require a metric nutdriver or a deep socket for a couple of bolts. Step 2. Use a 17 mm wrench to remove the large nut holding the aluminum impeller pulley, along with the flat and split lock washers. Also remove the part that locks the pulley onto the shaft. Step 3a. If there is not a manufacturing issue, the pulley will come off easily and you may proceed to thread the new belt around the power and idler pulleys. Step 3b. IF THE PULLEY DOES NOT COME OFF, you may need to get a wheeler puller tool to get it loose and off the shaft. Once the overly tight pulley is off, you may wish to file down the shaft near the end until the pulley slides on and off without much effort. (You may also wish to apply a dry silicone lubricant to the shaft to make the job easier next time.) Step 4. In order the install the new belt, feed it around the power pulley and the idler pulley controlled by the "engage" handle. With the impeller pulley still off its shaft, feed the belt around it, fitting the belt grooves into the pulley grooves. Step 5. The large aluminum can be replaced on its shaft, followed by the pulley lock, flat washer and split ring washer. Tighten the pulley lock nut, holding the impeller blades to keep the shaft from turning. Step 6. Replace the belt cover and the six bolts holding it in place.