JKP13GV1BB General Electric Wall Oven - Overview

Sections of the JKP13GV1BB

[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Door Handle End Cap – Part Number: WB7X7183
Door Handle End Cap
★★★★★
★★★★★
(40)
PartSelect #: PS256613
Manufacturer #: WB7X7183
This oven door handle end cap is used on both the left and right hand sides. Sold individually.
$25.95
  In Stock
Bake Element – Part Number: WB44K5013
Bake Element
★★★★★
★★★★★
(37)
PartSelect #: PS249249
Manufacturer #: WB44K5013
This bake element is used in ranges and located at the bottom of the oven. The bake element supplies heat for baking. If your symptoms include: your oven is not heating evenly, not starting, or the he...
$71.41
  In Stock
Single Heating Element Support Clip – Part Number: WB2X9719
Single Heating Element Support Clip
★★★★★
★★★★★
(7)
PartSelect #: PS243701
Manufacturer #: WB2X9719
The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this r...
$16.66
  In Stock
Broil Element - 240V – Part Number: WB44K5009
Broil Element - 240V
★★★★★
★★★★★
(20)
PartSelect #: PS249244
Manufacturer #: WB44K5009
This OEM-sourced broil element with push-on terminals is located on the roof of your oven cavity, providing heat from above to cook and heat your food. It requires a 240-volt power supply to function ...
$81.25
  In Stock
Oven Sensor – Part Number: WB21X5301
Oven Sensor
★★★★★
★★★★★
(5)
PartSelect #: PS236043
Manufacturer #: WB21X5301
It is possible that your oven is cold because of a fault in the temperature sensor. The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on the back wall near t...
$151.57
  In Stock
Screw – Part Number: WH2X930
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$12.21
  In Stock
Broiler Pan - Large – Part Number: WB48X10056
Broiler Pan - Large
★★★★★
★★★★★
(10)
PartSelect #: PS1517612
Manufacturer #: WB48X10056
This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures ...
$30.05
  In Stock
Screw – Part Number: WB1M1
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS234320
Manufacturer #: WB1M1
Sold Individually.
$7.77
  In Stock
Screw – Part Number: WB1X1130
Screw
★★★★★
★★★★★
(2)
PartSelect #: PS234427
Manufacturer #: WB1X1130
Sold Individually.
$8.30
  In Stock
Oven Rack – Part Number: WB48T10093
Oven Rack
★★★★★
★★★★★
(5)
PartSelect #: PS6447645
Manufacturer #: WB48T10093
Sold individually.
$79.38
  In Stock
Screw – Part Number: WB1K5157
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS234226
Manufacturer #: WB1K5157
This screw is black in color and sold individually.
$8.77
  In Stock
Door Handle – Part Number: WB15K5068
Door Handle
★★★★★
★★★★★
(7)
PartSelect #: PS231849
Manufacturer #: WB15K5068
This handle comes with the endcaps.
$110.71
  Special Order

Questions And Answers for JKP13GV1BB

Ask our experts a question about this model and we'll get back to you as soon as possible!

1 question answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Diane
January 2, 2020
When I press bake before I can set the temperature, it beeps and will not work! Everything else works fine! Broiler, and self cleaning works all elements get hot. It is just the bake that does not go on!
For model number JKP13GV1BB
PartSelect logo
Hi Diane, Thank you for your question. If the bake element will not turn on, then the issue is may be with the oven sensor, sometimes called the oven thermostat, and you will need to check it with a multi-meter. When testing the sensor with a multi-meter, the sensor should be tested at room temperature and it should be unplugged from the oven. You will need to measure the resistance between the two prongs at the end of the sensor connector. Replace the oven sensor if the reading is less than 900 Ohms or more than 1200 Ohms. If the sensor checks out fine, you will need to check the bake element, the electronic control board and the wiring between the parts to see which one is causing the issue. We hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the JKP13GV1BB

[Viewing 7 of 7]
Little to no heat when baking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Element will not heat
Fixed by
these parts
Fixing Fixing Fixing
Show All
Little to no heat when broiling
Fixed by
these parts
Fixing
Show All
Oven not heating evenly
Fixed by
these parts
Fixing Fixing Fixing
Show All
Oven is too hot
Fixed by
these parts
Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven tempature was approximately 150 degrees to low
This repair is EASY if you know how to use an ohm meter. If not, seek help for this step.

SYMPTOM:
The oven (JKP27WOP3WG or JKP27WP3WG and many ovens like it ) was not getting hot enough. Verifying the cooking temperature with an typical oven thermometer, I was able to determine that the oven was cooking temperature was about 150 degrees to low.

FAILURE POINTS:
There are two logical failure points (1) The oven sensor ( WB21X5301 about $75), or the (2) the controller board (PS238233 about $252). In my case it was the controller board. When replaced the oven worked beautifully.

REPAIR:
As with any repair, you MUST DISCONNECT POWER TO THE UNIT BEFORE SERVICING!!!

Pull oven from the wall:
- Disconnect power by flipping the circuit breaker to the OFF position.
- Remove the top flange / cowling from the top of the oven (it just pulls off)
- Remove two screws under the top flange / cowling
- The whole unit easily slides out, but it is highly recommended that you use two people to place the oven on the floor.

As a diagnostic between these two parts, if the oven sensors measure approximately 1.1K ohms of resistance at room temperature, then it is probably not the sensor. The oven sensor wires are connected to two white wires that run up to the controller board. You need to disconnect the oven sensor to make the measurement. You may either completely remove the oven sensor by cutting the wire (be sure to allow yourself enough slack so that they may be safely reconnected) where it connects to the white wires, OR, (preferred method) if leaving the oven sensor partially installed,
- Remove the top sheet metal cover (10 screws)
- Remove the service connect cover (2 screws - this is where the main Power cord comes into the unit)
- Disconnect the white wires from the controller board (this connector which also includes other circuits is on the left side when looking at the controller board).
- Remove two screws from oven sensor but just let in dangle down so that you can put the sensor in the ice water / boiling water.

Measure the resistance under the following conditions. Your ohm meter should read APPROXIMATELY...
- 1.02K ohms in ice water
- 1.09K ohms at room temperature
- 1.36K ohms in boiling water.
If you get approximately these readings, then it is NOT the oven sensor. If that checks out then re-install the sensor AND the connector.

If it is NOT the sensor, replace the controller board.
- Take a moment to write down the color of the wire to the LETTERING (N, L, G, C / COM,,,) on the controller board. The connectors are in different locations on the new controller board so the wire color to the letter designation is significant.
- Carefully remove the wires one at a time
- VERY carefully remove the keypad ribbon cable from the right side of the controller board.
-- The ribbon cable will disconnect by releasing some little pressure clips on the side of the connector.
- Remove the controller board (4 screws)
- Install new controller board (4 screws)
- VERY carefully connect the keypad ribbon cable on the right side.
-- Make sure that the connector is in the OPEN position first, then,
-- Slide in the cable ensuring that all parts of the ribbon made it into the connector, then
-- Press down on the connector locking tabs.
- Reconnect each wire to the correctly lettering on the board.
-- Again, the connectors MAY BE in a different order on the replacement controller board. Match color to letter.
- Reconnect the (5 wire?) connector that includes the white oven sensor wires.
- Make sure everything looks normal, (i.e. no wires are pinched, remove tools from top of oven area, etc.)
- Re-install top cover.
- Re-install service connect cover.

You can test the unit while it is out of the cabinet,
- Make SURE that all sheet metal covers are in place.
- Flip power breaker to "On".
- Test that oven gets to the desired temp.
Parts Used:
Oven Sensor
  • James from Austin, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
220 of 258 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bake element shorted out, sparking like a sparkler
first, made sure circuit breaker was off
second, used nut driver to remove 2 screws on old element, pulled it from the back of the oven
third, removed 2 wires from old element (spade connectors)
fourth, connected new element and pushed back into oven.
fifth, reinstalled 2 screws securing new element

this was all done by my 15 yr old son under my supervision.
Parts Used:
Bake Element
  • Carl from Wynnewood, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
89 of 97 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The broiler element caught fire and burned out while I was broiling a steak.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches, but I had not turned off the power.
So, I shorted out one of the wires. Then I turned off the power but was afraid to go any farther.
An appliance repairman was at my house that day fixing my dryer seal. He was able to pull the wires through the insulation successfully and install the broiler element. He did not charge me any extra for this little extra job. But I learned my lesson. Cut the power before you begin! He told me that I could have wound up with a much bigger repair if the short had been in the wire that is connected to the control panel of the oven. I was very lucky!
Parts Used:
Broil Element - 240V
  • Dianne from Rockville, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
67 of 75 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!