GTWN3000M1WS General Electric Washer - Overview
Sections of the GTWN3000M1WS
[Viewing 4 of 4]Manuals & Care Guides for GTWN3000M1WS
Click to downloadKeep searches simple, eg. "belt" or "pump".
Tub Dampening Strap
PartSelect #: PS271100
Manufacturer #: WH1X2727
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash c...
$9.60
In Stock
D-Shaped Knob Clip
PartSelect #: PS268493
Manufacturer #: WH01X10106
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the ti...
No Longer Available
Knob, Gray
PartSelect #: PS2370714
Manufacturer #: WH01X10462
This part is a replacement timer knob for your dryer. The knob fits onto a D-shaped shaft. To replace the knob, line up the back opening with the shaft and slide it in place. Make sure the dryer is tu...
$14.40
In Stock
Drain Hose
PartSelect #: PS890597
Manufacturer #: WH41X10096
The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drai...
$27.06
In Stock
Dual Action Agitator
PartSelect #: PS1482519
Manufacturer #: WH43X10034
This is a dual-action agitator for a washer. It is an OEM replacement part that is sourced from the manufacturer. The agitator tosses your clothes to clean them efficiently. This plastic dual-action a...
$75.24
In Stock
Drain Pump and Motor Assembly
PartSelect #: PS8768445
Manufacturer #: WH23X10030
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will not drain, there is...
$72.39
In Stock
Tub Seal
PartSelect #: PS4704237
Manufacturer #: WH02X10383
The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at ...
$16.71
In Stock
6-Rib Drive Belt
PartSelect #: PS1482278
Manufacturer #: WH01X10302
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
$25.73
In Stock
Tub Bearing Washer
PartSelect #: PS271509
Manufacturer #: WH2X1197
This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning smoothly during a w...
$9.96
In Stock
Split Ring
PartSelect #: PS1766022
Manufacturer #: WH02X10265
This split ring is supplied by the original equipment manufacturer, and it is designed to secure the tub bearing in washing machines. It is a circular metal ring, with an outer diameter of 2 inches. T...
$14.40
In Stock
Tub Bearing
PartSelect #: PS271510
Manufacturer #: WH2X1198
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you...
$27.50
In Stock
Agitator Coupling
PartSelect #: PS1482517
Manufacturer #: WH43X10032
Bolt not included. This part connects the transmission drive shaft to the agitator base.
$25.61
In Stock
Questions And Answers for GTWN3000M1WS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kathy
March 11, 2023
What are the outside dimensions of this unit, please. It is not listed in the manual I have and I need to replace with the same size unit.
For model number GTWN3000M1WS
Hello Kathy, thank you for your question. The Depth is 25.5" and Height 42" and Width is 27". We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Paula
February 20, 2024
can't find listing for cubic inch size of this model
For model number GTWN3000M1WS
Hi Paula, thank you for reaching out. The capacity of your model is 3.6 cubic feet/6220.8 cubic inches. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tayt
March 3, 2024
The washer was in the spin cycle and started making a loud grinding noise then stopped spinning/ draining water
For model number GTWN3000M1WS
Hi Tayt, thank you for reaching out. We have found that the issue is with the shaft and mode shifter assembly, part number PS2354082. It connects the motor with the wash plate and shifts the drive system between agitate and spin. You may need to replace it to fix the issue. We hope this information is useful!
Was this helpful?
Thank you for voting!
Related Parts:
Teresa
May 27, 2022
How to take off agitator mine has the dispenser for softener
For model number GTWN3000M1WS
Hello Teresa, thank you for your question. We do have the Dual Action Agitator PS1482519 and a video for you to access. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Was this helpful?
Thank you for voting!
Related Parts:
Kevin
October 17, 2022
Machine makes horrible noise during spin cycle
For model number GTWN3000M1WS
Hey Kevin, thank you for reaching out. We have researched your model and found that the issue is probably with the Tub Dampening Strap, part number PS271100. If that does not take care of the issue, then the problem is most likely to be related to the Tub Bearing, part number PS271510. We hope this helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the GTWN3000M1WS
[Viewing 13 of 13]Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Timer Not Working
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washing Machine was not draining water from tub.
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)<
... Read more
br />2. Removed the 2 bolts holding the Pump/Motor assembly to the machine.
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.
NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.
NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
Read less
Parts Used:
-
Gerald from Midlothian, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
302 of 330 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washing machine would not go through all cycles or agitate
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
Parts Used:
-
Brian from Millerplace, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
227 of 287 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
machine would not drain all other functions seemed o.k
Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts
... Read more
list complete with instructions on how to remove the FRONT panel. Once I got inside it was easy to locate the pump. I ran the drain cycle for a moment to see if the pump turned at all. The original had an exposed fan so it was easy to see that indeed the motor was not turning. I inspected all the hose and electrical connections to make sure I had the tools I'd need and the savvy to replace the part(s) if I could locate them. I'm not much of a web-head, so I was a little surprised when I typed G.E. appliances and the search took me to partselect.com where I was pretty much coached through the procedure before I even ordered the part. The box arrived ahead of schedule (yay) and when I looked at the pump it didn't look much like the one I was replacing. But then I realized it was the same thing just ten years more advanced. I used a small pair of vise grips to pinch and lock the pipe clamps open. I know there is a plier made for this, but... Anyways, after loosening the clamps and sliding them away from the pump I pulled the hoses off and let the last of the rinse water still in them run down my shirt sleeve to my elbow. (optional, not recommended) Thus refreshed I then rummaged through my socket set and found what I needed to remove the 2 sheet metal mounting screws and disconnected the 2 power leads. I removed the faulty pump and proudly showed it to my wife. Unimpressed, she asked how much longer. I quickly reversed the procedure to install the new unit and confidently piled in a load of laundry. The cycle completed just fine and has done so since. I will and have recommmended partselect.com to friends and will use it again for sure.
Read less
Parts Used:
-
douglas from danby, VT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
86 of 90 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!