This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found...
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place o...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs ...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to create a watertight seal...
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
January 30, 2023
Tub drains after spin cycle , but leaves the clothes soaking wet .
For model number AWN311SP111TW01
Hi Gary,
Thank you for your question. If your clothes are still wet once the cycle has completed, you may be loading too many items into the washer. Overloading the washer may cause an imbalance. This reduces the speed of the washer and the clothes will remain wet. If this is not the issue and the washer is not spinning properly, you will need to check the lid switch and the belt. If the washer is not draining correctly, you will need to check the drain hose to see if it is kinked and make sure that it is properly positioned. Check the drain filter and the pump for clogs and check the drain pump to see if it is working properly. Once you have determined the part you need, please call customer service. We look forward to hearing from you!
Our washer started squeaking just a little and now it will not go into high speed spin. Can you tell me what is wrong with it?
For model number AWN311SP111TW01
Hello Victor, thank you for contacting us. We have concluded that the issue is most probably with the drive belt, part number PS11740577. We would recommend checking it to solve the problem. Glad to be of help!
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.
I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber
... Read more section).
So, I finished draining, removed the hose (required pliers to squeeze off a hose clamp).
Upon inspecting the hose, it was also apparent that the hole was caused by rubbing against a support bracket for the motor. This should not happen, but it did because the plastic standoff supposed to keep the hose away from the bracket was installed 180 degrees backwards.
So, I simply replaced the hose and turned the bracket around to the correct orientation.
Everything worked as planned and my repair cost was much less than if I had called someone out.
The washer is four years old. This is the second time I needed to replace this same drain hose on this same washer since I had the machine There is only my wife ant myself maybe, 2 -3 medium size loads per week - why I would have two drain lines develop the same problem in almost the same location in two years is disconcerting
... Read more There must be a design problem with the clear plastic hose - Suggest Maytag go to a thick walled rubber hose The hole is alway inside the washer on the bottom just after the hose bracket - I suspect that something rubbing causing a small pin hole to develop - when the condition first starts it is very difficult to located -There will be water under the washer Run the washer and discharge the water - to locate
The replacement must be made through the lower front removable panel - and is easier to do if the pump return hose is also disconnected from the pump
Be very carful with the thin wall replacement hose - very light weight plastic - do not pull across the floor of washer - it could easily get damaged
Your company did a get job getting the part to me - The Fed Ex track system was great I could tell exactly where the delivery was al all times -