11049962603 Kenmore Washer - Overview

Sections of the 11049962603

[Viewing 7 of 7]

Manuals & Care Guides for 11049962603

Click to download
Keep searches simple, eg. "belt" or "pump".
Washer Door Bellow – Part Number: WP8182119
Washer Door Bellow
★★★★★
★★★★★
(32)
PartSelect #: PS11744957
Manufacturer #: WP8182119
This is a door bellow, also known as a door gasket or seal, that is compatible with washing machines. Door bellows are used as a method to seal the inner drum of the washing machine and the soapy wate...
13% OFF
$156.13
$179.55
  In Stock
Drain Pump Kit – Part Number: 280187
Drain Pump Kit
★★★★★
★★★★★
(56)
PartSelect #: PS1485610
Manufacturer #: 280187
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.
$150.58
  In Stock
Washing Machine Door Hinge – Part Number: WP8183202
Washing Machine Door Hinge
★★★★★
★★★★★
(45)
PartSelect #: PS11745072
Manufacturer #: WP8183202
This door hinge is a genuine OEM replacement part that is made to fit various front-load washing machines. It is a high-quality replacement that is guaranteed to fit with your model. The door hinge co...
$125.06
  In Stock
Water Inlet Valve – Part Number: WP8182862
Water Inlet Valve
★★★★★
★★★★★
(21)
PartSelect #: PS11745050
Manufacturer #: WP8182862
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$69.63
  In Stock
Shock Absorber – Part Number: W10822553
Shock Absorber
★★★★★
★★★★★
(6)
PartSelect #: PS11723173
Manufacturer #: W10822553
Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber is for washers. Shock absorber absorbs the vibrations and movements of the oute...
$57.13
  In Stock
Touch-Up Paint - White – Part Number: 72017
Touch-Up Paint - White
★★★★★
★★★★★
(2)
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
  In Stock
Screw – Part Number: WP488729
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS11742721
Manufacturer #: WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
$7.91
  In Stock
Hose Clamp – Part Number: WP285655
Hose Clamp
★★★★★
★★★★★
(2)
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.09
  In Stock
Bellow to Outer Tub Clamp – Part Number: WP8182210
Bellow to Outer Tub Clamp
★★★★★
★★★★★
(5)
PartSelect #: PS11744959
Manufacturer #: WP8182210
Used to help hold your bellow in place on your washer.
$36.94
  In Stock
Bellow Clamp – Part Number: W10902779
Bellow Clamp
★★★★★
★★★★★
(8)
PartSelect #: PS11765855
Manufacturer #: W10902779
This is the replacement bellow clamp for your washer. It approximately 16 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place on t...
$32.23
  In Stock
Drive Belt – Part Number: WPW10388414
Drive Belt
★★★★★
★★★★★
(12)
PartSelect #: PS11754067
Manufacturer #: WPW10388414
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear. NOTE: Per Manufacture, belt measures 48.22" long uninstall...
$52.80
  In Stock
Pump Hose – Part Number: WPW10467168
Pump Hose
★★★★★
★★★★★
(4)
PartSelect #: PS11755212
Manufacturer #: WPW10467168
This hose attaches to water pump assembly. NOTE: As per the manufacture if the washer has an Eco Ball, it's no longer needed when the new hose is installed.
$37.48
  In Stock

Questions And Answers for 11049962603

Ask our experts a question about this model and we'll get back to you as soon as possible!

2 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brenda
March 25, 2023
Something maybe in washer causing a snag in nylon or delicate material
For model number 11049962603
PartSelect logo
Hi Brenda, thank you for reaching out. We have narrowed the issue down to the following parts: the baffle, part number PS11751113, and the door bellow, part number PS11744957. We hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
Roseann
June 26, 2023
Ned a Rim around the door
For model number 11049962603
PartSelect logo
Hi Roseann, thank you for your inquiry. The part you are looking for is the door boot seal, part number PS11744957. We hope this information is useful!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1

Common Symptoms of the 11049962603

[Viewing 14 of 14]
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing Fixing
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
Fixing
Show All
Water Filling Issues
Fixed by
these parts
Fixing
Show All
Draining Issues
Fixed by
these parts
Fixing
Show All
Burning smell
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing
Show All
Shaking and Moving
Fixed by
these parts
Fixing
Show All
Locking Issues
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bellows were moldy, needed to replace
The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow.
Use a small screwdriver or other to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.

The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily.
When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow.
Push as much of the bellow into the washer as possible to get it out of the way.

Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and the secures it to the portion that holds the basket.
This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way.
Loosen the hose clamp almost all of the way, not necessary to have the hose clamp come completely apart.
You can now remove the entire hose clamp from around the bellow by pulling it forward.
You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out.
Pull the old bellow completely out, very easy to do.

Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side.
You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.

Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force.
As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.

Now it is time to install the Hose clamp. Un bend anything that might have bent on the clamp. With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop.
Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.

Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. This w
Parts Used:
Washer Door Bellow
  • Franck from Annandale, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
364 of 391 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not drain ,F02 and SUD code displaying
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas
Parts Used:
Drain Pump Kit
  • Donald from Wichita, KS
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Socket set
233 of 245 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer made loud banging noise during spin cycle
I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the washer was back in service.
Parts Used:
Drum Drive Pulley Drive Belt
  • Francis from Rochester, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
117 of 146 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!