Lawn Mower Engines

Popular Lawn Mower Engines

Your Price
$27.50
  In Stock
Lawn Mower Gear-Governor
★★★★★
★★★★★
1 Review
PartSelect Number PS9151758
Manufacturer Part Number 793338
Installation Instructions
rodney from MUSCATINE, IA
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet to remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions Read more...
Your Price
$6.89
  On Order
Lawn Mower Rod-Push (Steel)
★★★★★
★★★★★
1 Review
PartSelect Number PS9062983
Manufacturer Part Number 690981
This is a replacement steel push rod for your lawn tractor engine. The engine will have two push rods; one made of steel, and one made of aluminum. This part is made of steel and is approximately 6 inches in length. Make sure you order the correct replacement rod, as they are different. If the engine is unable to operate at full power, you may have a bent or broken push rod. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
Installation Instructions
Robert from WHITMAN, MA
the head blew a vaulve guide destoying push rods
about 6 hours to tear down and replace don't do it in the hot sun needed more breaks takes longer, but the new factory heads did it started up 185 lbs of compression almost back to new, so much more power than old one's. FYI take off the motor cover every year clean out the debris (grass-mouse nest- and oil) it blocks the air and COOKS THE HEAD it only takes short time and will make that motor last a little longer but it is a BRIGGS engine Read more...
Your Price
$9.98
  In Stock
Lawn Mower Rod-Push (Exhaust)
PartSelect Number PS9066108
Manufacturer Part Number 692011
Your Price
$189.84
  Special Order
Lawn Mower Head--Cylinder
PartSelect Number PS9141923
Manufacturer Part Number 796026
Your Price
$12.91
  In Stock
Lawn Mower Adjuster--Rocker Arm
PartSelect Number PS9066105
Manufacturer Part Number 691986
Your Price
$45.44
  In Stock
Lawn Mower Ring Set
PartSelect Number PS9306695
Manufacturer Part Number 792026
Your Price
$7.31
  In Stock
Lawn Mower Reed--Breather
PartSelect Number PS9064775
Manufacturer Part Number 697124
Your Price
$181.00
  On Order
Lawn Mower Cylinder Head
PartSelect Number PS9152257
Manufacturer Part Number 796231
This is a replacement cylinder head kit for your small engine. It contains everything you will need to replace a damaged cylinder head. This is a 12-piece kit that is sold as a unit. This is an OEM part sourced directly from the manufacturer. The cylinder head is a critical part of your small engine. If it is damaged, your engine may not run at top performance, and depending on the severity of the damage, may not run at all.
Installation Instructions
Robert from WHITMAN, MA
the head blew a vaulve guide destoying push rods
about 6 hours to tear down and replace don't do it in the hot sun needed more breaks takes longer, but the new factory heads did it started up 185 lbs of compression almost back to new, so much more power than old one's. FYI take off the motor cover every year clean out the debris (grass-mouse nest- and oil) it blocks the air and COOKS THE HEAD it only takes short time and will make that motor last a little longer but it is a BRIGGS engine Read more...
Your Price
$7.96
  In Stock
Lawn Mower Keeper-Valve
PartSelect Number PS9281494
Manufacturer Part Number 499586
Your Price
$12.31
  In Stock
Lawn Mower Rod-Push (Exhaust)(Aluminum)
PartSelect Number PS9063658
Manufacturer Part Number 691758
Installation Instructions
GERALD from CLIO, MI
Exhaust push rod
Reverse of how i took broken exhuast value out.
It was simple just watch what you do. Also make sure you lash the value. U tube it.
Read more...

Lawn Mower Engine Brands