Kenmore Dryer Springs and Shock Absorbers
Popular Kenmore Dryer Springs and Shock Absorbers
Your Price
$12.98
In Stock
Kenmore Dryer Spring
When I emailed customer service to complain, I never received any response. I can't believe that customer service can be so unimportant in such a competitive marketplace. And with the power of social media, you would think customer service would be a big differentiator.
I ended having to buy another part (the igniter). I found a different vendor with better prices and a commitment to satisfying customers. I got my part in 3 days for cheaper shipping than the starting point of Parts Select shipping. So I guess I should thank Parts Select for forcing me to look elsewhere because I found a better place with better prices and better shipping and better customer service! Read more...
PartSelect Number PS11754856
Manufacturer Part Number WPW10446781
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Rod from YORBA LINDA, CA
Loud Dryer
Please do not buy parts from Parts Select. My order was not shipped the next day (as advertised on the web site), but instead 3 days later. I paid an extra couple of dollars for expedited shipping, which did made no difference (except for a couple of extra dollars for Parts Select to pocket). When I emailed customer service to complain, I never received any response. I can't believe that customer service can be so unimportant in such a competitive marketplace. And with the power of social media, you would think customer service would be a big differentiator.
I ended having to buy another part (the igniter). I found a different vendor with better prices and a commitment to satisfying customers. I got my part in 3 days for cheaper shipping than the starting point of Parts Select shipping. So I guess I should thank Parts Select for forcing me to look elsewhere because I found a better place with better prices and better shipping and better customer service! Read more...
Kenmore Dryer Idler Arm Spring
DISCONNECT ELECTRICITY and GAS LINES
1.popped top by pushing and prying at front /top clips about 2-3in. in from side edges. lifted it off
2. removed the front panel by removing the 2 top front screws from the inside, then the two lower screws from the front after removing the small white plastic hole covers. disconnected the multiplug electric connector top right. set panel aside.
3.remove small back panel.and loosened belt.(observe belt path and idle pulley assy.
4. lifted drum and slid it out the front.
5. using socket, removed rear plastic bearing housing and replaced the same. be careful of observing the small ball bearing and the small piece on outside back panel. replace the same. you wil probably need a second set of hands to hold the piece on the outside when screwing in the screws from the inside.
6. unscew the "bearing" from the rear of the drum and replace with new one.(the screws are self-tapping and go in HARD!!)
7. apply lubricant liberally to plastic bearing holder
8. place new belt around drum(rubber side against drum cloth side out.
9. idle pulley assy. is removed by removing spring and just sliding assy out of holder. replace with new
10. replace drum and belt
11. take front panel and remove top drum glide and lower basket seal.( i marked where the two seal/glide come together with a marker )
12. scrape and remove as much felt and possible. I then used "goo gone" to remove all the glue. clean well and using the provided high temp adhesive reattached glide and seal.
13. reassemble and enjoy your NEW? dryer Read more...
PartSelect Number PS418263
Manufacturer Part Number 131601000
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
john from owego, NY
clothes got caught , burned and ripped on front of drum
I felt ,if I was going to replace the top drum glide and lower basket seal, I might as well replace the belt ,bearing assembly and the idle pulley assembly and avoid having to replace these sooner than later. All of the parts showed alot of wear and the belt like all drive belts, should be changed every 5-6 years.DISCONNECT ELECTRICITY and GAS LINES
1.popped top by pushing and prying at front /top clips about 2-3in. in from side edges. lifted it off
2. removed the front panel by removing the 2 top front screws from the inside, then the two lower screws from the front after removing the small white plastic hole covers. disconnected the multiplug electric connector top right. set panel aside.
3.remove small back panel.and loosened belt.(observe belt path and idle pulley assy.
4. lifted drum and slid it out the front.
5. using socket, removed rear plastic bearing housing and replaced the same. be careful of observing the small ball bearing and the small piece on outside back panel. replace the same. you wil probably need a second set of hands to hold the piece on the outside when screwing in the screws from the inside.
6. unscew the "bearing" from the rear of the drum and replace with new one.(the screws are self-tapping and go in HARD!!)
7. apply lubricant liberally to plastic bearing holder
8. place new belt around drum(rubber side against drum cloth side out.
9. idle pulley assy. is removed by removing spring and just sliding assy out of holder. replace with new
10. replace drum and belt
11. take front panel and remove top drum glide and lower basket seal.( i marked where the two seal/glide come together with a marker )
12. scrape and remove as much felt and possible. I then used "goo gone" to remove all the glue. clean well and using the provided high temp adhesive reattached glide and seal.
13. reassemble and enjoy your NEW? dryer Read more...
Kenmore Dryer Single Door Spring
PartSelect Number PS11741307
Manufacturer Part Number WP337186
***The manufacturer suggests to replace both springs at the same time.***
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
Terry from ONAMIA, MN
Door springs and cables were broke, and the door catch was broke.
Removed screws by lint trap, used putty knife to pry top of dryer apart, use nut driver for two bolts that hold the front panel of dryer on, replaced parts, put it back together.
Read more...
Kenmore Dryer Spring, Lint Screen Door
PartSelect Number PS11741474
Manufacturer Part Number WP3394986
Kenmore Dryer Door Spring
PartSelect Number PS11748045
Manufacturer Part Number WPW10041960
Sold individually.
Kenmore Dryer Idler Spring
I've had the dryer more than 20 years, so I am really glad such a simple repair will keep it going!
Parts arrived very quickly - great service from PastSelect! Read more...
PartSelect Number PS459789
Manufacturer Part Number 5303281085
With the spring it helps keep the tension in the belt by pulling the idler pulley.
Installation Instructions
Patricia from Clifton Park, NY
Belt Broke
Very easy install. Removed the top and front of dryer, and put new belt on drum. Also replaced Idler Pulley (altho didn't really need to.)I've had the dryer more than 20 years, so I am really glad such a simple repair will keep it going!
Parts arrived very quickly - great service from PastSelect! Read more...
Related Kenmore Dryer Parts
- All Kenmore Dryer parts
- Kenmore Dryer Belts
- Kenmore Dryer Brackets and Flanges
- Kenmore Dryer Caps and Lids
- Kenmore Dryer Circuit Boards and Touch Pads
- Kenmore Dryer Doors
- Kenmore Dryer Drums and Tubs
- Kenmore Dryer Ducts and Vents
- Kenmore Dryer Elements and Burners
- Kenmore Dryer Fans and Blowers
- Kenmore Dryer Filters
- Kenmore Dryer Fuses
- Kenmore Dryer Handles
- Kenmore Dryer Hardware
- Kenmore Dryer Hinges
- Kenmore Dryer Hoses and Tubes
- Kenmore Dryer Knobs
- Kenmore Dryer Latches
- Kenmore Dryer Lights and Bulbs
- Kenmore Dryer Motors
- Kenmore Dryer Panels
- Kenmore Dryer Pulleys
- Kenmore Dryer Seals and Gaskets
- Kenmore Dryer Sensors
- Kenmore Dryer Switches
- Kenmore Dryer Thermostats
- Kenmore Dryer Timers
- Kenmore Dryer Valves
- Kenmore Dryer Wheels and Rollers
- Kenmore Dryer Wire Plugs and Connectors